2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

Fuel Injector Circuit

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The fuel injector assemblies are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

Refer to DTC P0300 (Click here).

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)
A208644E07
  1. Disconnect the fuel injector assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C1-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C2-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C3-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C4-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C5-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C6-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)

  1. Reconnect the fuel injector assembly connector.



NG
Go to step 4
OK


2. INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the fuel injector assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C1-2 - C37-6 (#10)
    Always
    Below 1 Ω
    C2-2 - C37-1 (#20)
    Always
    Below 1 Ω
    C3-2 - C37-7 (#30)
    Always
    Below 1 Ω
    C4-2 - C37-2 (#40)
    Always
    Below 1 Ω
    C5-2 - C37-8 (#50)
    Always
    Below 1 Ω
    C6-2 - C37-3 (#60)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C1-2 or C37-6 (#10) - Body ground
    Always
    10 kΩ or higher
    C2-2 or C37-1 (#20) - Body ground
    Always
    10 kΩ or higher
    C3-2 or C37-7 (#30) - Body ground
    Always
    10 kΩ or higher
    C4-2 or C37-2 (#40) - Body ground
    Always
    10 kΩ or higher
    C5-2 or C37-8 (#50) - Body ground
    Always
    10 kΩ or higher
    C6-2 or C37-3 (#60) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the fuel injector assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

4. INSPECT NO. 1 INTEGRATION RELAY (IG2)
  1. Inspect the No. 1 integration relay (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY (IG2)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL INJECTOR ASSEMBLY)


← Fuel Pump Control Circuit (from Aug 2014)Fuel Injector Circuit (from Aug 2014) →