2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REASSEMBLY

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
  1. Clean the front seat frame assembly with adjuster RH surface.

  1. B294332
    Install a new front seat cushion edge protector RH as shown in the illustration.


2. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR

  1. B294331
    Install the 2 front seat cushion edge protectors.


3. INSTALL OUTER VERTICAL ADJUSTER BRACKET COVER
  1. Attach the claw to install the outer vertical adjuster bracket cover.

  1. Install the screw.


4. INSTALL RECLINING ADJUSTER OUTSIDE COVER LH
  1. Install the reclining adjuster outside cover LH with the screw.


5. INSTALL RECLINING ADJUSTER OUTSIDE COVER RH

HINT:
Use the same procedure described for the LH side.


6. INSTALL RECLINING ADJUSTER INSIDE COVER LH
  1. Attach the guide to install the reclining adjuster inside cover LH.

  1. Install the screw.


7. INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedure described for the LH side.


8. INSTALL FRONT SEAT INNER CUSHION SHIELD RH
  1. Attach the hook and claw to install the front seat inner cushion shield RH.

  1. Install the 2 screws.


9. INSTALL CENTER SEAT HINGE COVER
  1. Attach the guide to install the center seat hinge cover.

  1. Install the screw.


10. INSTALL FRONT SEATBACK PROTECTOR
  1. Remove any double-sided tape remaining on the front seat frame assembly with adjuster RH.

  1. B294326E01
    Apply double-sided tape as shown in the illustration.
    Text in Illustration 
    *1
    Double-sided Tape

  1. Install the front seatback protector.


11. INSTALL SEPARATE TYPE FRONT SEATBACK PAD
  1. Install the separate type front seatback pad to the front seat frame assembly with adjuster RH.


12. INSTALL SEPARATE TYPE FRONT SEATBACK COVER
  1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. Attach the 4 claws to install the 2 front seat headrest supports.

  1. Attach the fastening tape and hook.

    B294323E01

    Text in Illustration 
    *1
    Hog Ring Pliers
    *2
    Hog Ring
    *3
    Hook
    *4
    Fastening Tape

  1. B294321E01
    Using hog ring pliers, attach the 2 straps of the separate type front seatback cover to the front seat frame assembly with adjuster RH with new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

  1. B294319E01
    Using hog ring pliers, attach the separate type front seatback cover with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers


13. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

  1. B294317E02
    Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers
    *2
    Tack pin

  1. Using a tacker, install the separate type front seat cushion cover to the separate type front seat cushion pad with a new tack pin as shown in the illustration.

  1. B301193E01
    Attach the hook.
    Text in Illustration 
    *1
    Hook
    *2
    Hog Ring
    *3
    Hog Ring Pliers

  1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.

    NOTICE:
    When installing the hog rings, avoid wrinkling the cover.


14. INSTALL CONNECTOR HOLDER
  1. Attach the claw to install the connector holder.


15. INSTALL FRONT SEAT CUSHION COVER WITH PAD
  1. Set the front seat cushion cover with pad in place.

  1. Attach the 2 clamps to install the connector holder.

  1. Attach the hooks to install the front seat cushion cover with pad.

  1. Using hog ring pliers, install new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. Install the clip.

    B294312E01

    Text in Illustration 
    *1
    Hog Ring Pliers
    *2
    Hog Ring

  1. B294310
    Return the 2 cushion edge tabs to their original positions.

    NOTICE:
    Be careful not to break the cushion edge tabs.


16. INSTALL FRONT SEATBACK SIDE COVER SUB-ASSEMBLY RH
  1. Install the front seatback side cover sub-assembly RH to the front seatback inside pad RH.

  1. Install the front seatback side cover sub-assembly RH with the front seatback inside pad RH.

  1. Attach the hook to close the front seatback side cover sub-assembly RH.


17. INSTALL FRONT SEAT ARMREST HOLE BOARD COVER
  1. Install the front seat armrest hole board cover to the seat armrest assembly RH.


18. INSTALL SEAT ARMREST ASSEMBLY RH
  1. Install the seat armrest assembly RH with the bolt.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


19. INSTALL INNER SEAT BRACKET ASSEMBLY RH
  1. Install the inner seat bracket assembly RH with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Lift up the seat armrest assembly RH and place it in the normal seating position.


20. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH
  1. Attach the hook to install the front seat lower cushion shield RH.

  1. Install the 2 screws.


21. INSTALL FRONT SEAT HINGE COVER RH
  1. Attach the 2 hooks to install the front seat hinge cover RH.

  1. Install the 2 screws.


22. INSTALL FRONT SEAT HINGE KNOB

  1. B292633
    Twist the front seat hinge knob in the direction indicated by the arrow to install it.


23. INSTALL FRONT SEAT CUSHION SHIELD RH

  1. B294305E01
    Attach the guide and clip.

  1. Attach the claw and hook to install the front seat cushion shield RH.

    Text in Illustration 
    *1
    Guide
    *2
    Hook

  1. Install the screw.

  1. Attach the 2 rubber bands.


24. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH
  1. Attach the claw to install the reclining adjuster release handle RH.


25. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH

  1. B295930
    Pass the front seat inner belt assembly RH through the band of the front seat cushion cover as shown in the illustration.

  1. B294015E01
    Install the front seat inner belt assembly RH to the front seat assembly RH with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Make sure that the protruding part of the front seat inner belt assembly RH is not positioned on top of the frame.

    Text in Illustration 
    *a
    Protruding Part

  1. Attach the 3 wire harness clamps and connect the occupant detection sensor connector.

  1. Install the front seat assembly RH (Click here).


26. INSTALL SEAT ADJUSTER COVER CAP RH
  1. Install the 2 seat adjuster cover caps.

← DISASSEMBLY (from Aug 2014)REASSEMBLY (from Aug 2014) →