2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 13 clips and upper radiator support seal.


3. REMOVE FRONT FENDER SIDE PANEL PROTECTOR LH

  1. E199696
    Detach the 3 clips and guide, and remove the front fender side panel protector.


4. REMOVE FRONT FENDER SIDE PANEL PROTECTOR RH

HINT:
Use the same procedure for the RH side and LH side.


5. REMOVE FRONT FENDER TO COWL SIDE SEAL LH

  1. E198988
    Detach the 5 claws and remove the front fender to cowl side seal LH.


6. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:
Use the same procedure for the RH side and LH side.


7. REMOVE WINDSHIELD WIPER ARM COVER

  1. E198979E01
    Using a screwdriver, detach the 3 claws and remove the wiper arm cover.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    1. Tape the screwdriver tip before use.
    2. Use the same procedure for the RH and LH sides.


8. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E197606
    Remove the nut and front wiper arm and blade assembly LH.


9. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E197608
    Remove the nut and front wiper arm and blade assembly RH.


10. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E197614E01
    Remove the 2 clips.

  1. Detach the 6 claws and guide (A).

    Text in Illustration 
    *1
    Guide A
    *2
    Guide B

  1. Disengage the 10 guides (B) and pull out the cowl top ventilator louver sub-assembly.


11. REMOVE WINDSHIELD LOWER OUTSIDE MOULDING LH

  1. B241712
    Remove the windshield outside moulding.

    1. Put protective tape around the moulding.

    2. Using a moulding remover, detach the 5 clips and remove the moulding.

      NOTICE:
      1. When removing the windshield outside moulding, be careful not to damage the roof drip side finish moulding clip.
      2. If a roof drip side finish moulding clip is damaged or becomes detached from the vehicle, replace it with a new one.


12. REMOVE WINDSHIELD LOWER OUTSIDE MOULDING RH

HINT:
Use the same procedure described for the LH side.


13. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

B238732E01
  1. Put protective tape around the door scuff plate.

  1. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


14. REMOVE DOOR SCUFF PLATE ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


15. REMOVE COWL SIDE TRIM BOARD LH

B238734
  1. Remove the clip.

  1. Detach the clip and claw and remove the cowl side trim board.


16. REMOVE COWL SIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.


17. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

B238778
  1. Remove the front door opening trim weatherstrip.


18. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure described for the LH side.


19. REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH

B238741E01

HINT:
Use the same procedure for the other front No. 1 assist grip plug.

  1. Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


20. REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH

HINT:
Use the same procedure described for the LH side.


21. REMOVE NO. 1 ASSIST GRIP

B238742

HINT:
Use the same procedure for the other No. 1 assist grip.

  1. Remove the 2 bolts.

  1. Detach the 2 claws and remove the No. 1 assist grip.


22. REMOVE FRONT PILLAR GARNISH LH

B238743
  1. Detach the 3 guides and remove the front pillar garnish.

  1. B238744E01
    w/ Curtain Shield Airbag:
    Protect the curtain shield airbag assembly.

    1. Completely cover the airbag with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

      Text in Illustration 
      *1
      Curtain Shield Airbag Assembly
      *2
      Adhesive Tape
      *3
      Protective Cover


23. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.


24. REMOVE VISOR BRACKET COVER LH

B181706

HINT:
Use the same procedure for the other visor bracket cover.

  1. Detach the 4 claws and remove the visor bracket cover.


25. REMOVE VISOR BRACKET COVER RH

HINT:
Use the same procedure described for the LH side.


26. REMOVE VISOR ASSEMBLY LH

B181707
  1. Remove the 2 screws and visor.


27. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


28. REMOVE VISOR HOLDER

B151362E02

HINT:
Use the same procedure for the other visor holder.

  1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

  1. Detach the 2 claws and remove the visor holder.


29. REMOVE MAP LIGHT ASSEMBLY

  1. E198057
    Detach the 4 clips.

  1. Disconnect the connector and remove the map light.


30. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

  1. E197772
    Detach the 2 claws and remove the rain sensor cover.


31. REMOVE RAIN SENSOR (w/ Rain Sensor)

  1. E197773
    Disconnect the connector.

  1. E179753E02
    Release the stopper by pulling it down.
    Text in Illustration 
    *1
    Stopper

  1. Remove the rain sensor as shown in the illustration.


32. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

  1. B064964E10
    Push the cover in the direction indicated by the arrows labeled A and remove it.

  1. While holding down the claw in the direction of the black arrow labeled B, slide the mirror in the direction of the white arrow and remove it.

    Text in Illustration 
    *1
    Cover
    *2
    Claw


33. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

  1. B175048
    Detach the 2 claws and slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration.

  1. B175049
    Detach the 2 claws and remove the inner rear view mirror stay holder cover.


34. REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

  1. B175042
    Disconnect the connector.

  1. Using a T20 "TORX" socket wrench, remove the screw and inner rear view mirror.


35. REMOVE ROOF HEADLINING ASSEMBLY
  1. w/ Sliding Roof:

    1. Partially remove the roof headlining.

      HINT:
      It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.
      Refer to the following procedures (Click here).

  1. w/o Sliding Roof:

    1. Partially remove the roof headlining.

      HINT:
      It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the windshield glass can be removed in a later step.
      Refer to the following procedures (Click here).


36. REMOVE WINDSHIELD GLASS

NOTICE:
  1. There are No. 1 and No. 2 stoppers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.
  2. To prevent the windshield glass from dropping when performing this operation, be sure to hold the windshield glass using suction cups.

HINT:
Depending on the vehicle specifications, a 1-piece or 2-piece type stopper is used.


B238992E01
Text in Illustration 
*A
for 1-piece Type
*B
for 2-piece Type
*1
No. 1 Windshield Glass Stopper
*2
No. 2 Windshield Glass Stopper

  1. B238993E01
    Apply protective tape to the outer surface of the vehicle body to prevent scratches.
    Text in Illustration 
    *1
    Protective Tape

  1. B238994E01
    From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.

  1. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

    NOTICE:
    1. When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.
    2. To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.

    Text in Illustration 
    *1
    Plastic Sheet
    *2
    Piano Wire
    *3
    Wooden Blocks
    *4
    Protective Tape
    *5
    Stopper

  1. B238990E01
    Place matchmarks over the glass and vehicle body at the locations indicated in the illustration.

    NOTICE:
    Matchmarks do not need to be placed if not reusing the glass.

    Text in Illustration 
    *a
    Matchmark

  1. w/ Windshield Deicer System:
    Disconnect the windshield deicer connector.

  1. Cut through the adhesive by pulling the piano wire around the glass.

    NOTICE:
    Leave as much adhesive on the vehicle body as possible when removing the glass.

  1. Disconnect the stoppers.

  1. B238991
    Using suction cups, remove the glass.


37. REMOVE WINDSHIELD GLASS ADHESIVE DAM
  1. Using a scraper, remove the adhesive dam.

    NOTICE:
    1. Be careful not to damage the windshield glass.
    2. Be sure to replace the adhesive dam with a new one.


38. REMOVE WINDSHIELD OUTSIDE MOULDING
  1. Using a scraper, remove the moulding.

    NOTICE:
    1. Be careful not to damage the windshield glass.
    2. Be sure to replace the moulding with a new one.


39. REMOVE NO. 2 WINDSHIELD GLASS STOPPER
  1. Using a scraper, remove the 2 stoppers.

    NOTICE:
    1. Be careful not to damage the windshield glass.
    2. Be sure to replace the stoppers with new ones.


40. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

  1. B238995
    Remove the 2 No. 1 stoppers.

    NOTICE:
    Be sure to replace the No. 1 stoppers with new ones.


41. REMOVE NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

B241713
  1. Remove the 5 No. 1 windshield moulding clips.

    HINT:
    Use the same procedure to remove the 5 clips on the other side.


42. REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP

HINT:
Perform the following procedures if replacing any No. 3 windshield outside moulding clips.

  1. Put a 4 mm (0.157 in.) drill bit into a drill.

  1. Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill.

    HINT:
    Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

  1. B238988E01
    Lightly press the drill against the No. 3 windshield outside moulding clips, drill off the flanges of the No. 3 windshield outside moulding clips, and remove it.

    NOTICE:
    1. Pressing the drill too firmly will cause the No. 3 windshield outside moulding clip to turn and result in the No. 3 windshield outside moulding clip not being drilled through.
    2. Do not pry the No. 3 windshield outside moulding clips with the drill because this may cause damage to the installation holes of the No. 3 windshield outside moulding clips or the drill bit.

    CAUTION:
    Be careful of the drilled No. 3 windshield outside moulding clips as they may become hot.

  1. Using a vacuum cleaner, remove the No. 3 windshield outside moulding clip fragments and shavings from the drilled areas.

    HINT:
    Use the same procedure to remove clips on the other side.


43. CLEAN WINDSHIELD GLASS

B106929
  1. Using a scraper, remove the damaged stoppers, dam and adhesive sticking to the glass.

  1. Clean the outer circumference of the glass with non-residue solvent.

    NOTICE:
    1. Do not touch the surface of the glass after cleaning it.
    2. Be careful not to damage the glass.
    3. Even if using new glass, clean the glass with non-residue solvent.


44. CLEAN VEHICLE BODY

B106081E18
  1. Clean and shape the contact surface of the vehicle body.

    1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

      NOTICE:
      Be careful not to damage the vehicle body.

      HINT:
      Leave as much adhesive on the vehicle body as possible.

  1. Clean the contact surface of the vehicle body with cleaner.

    HINT:
    Even if all the adhesive has been removed, clean the vehicle body.

    Text in Illustration 
    *1
    Adhesive
    *2
    Vehicle Body

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →