2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

Skid Control ECU Communication Stop Mode

Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Detection Item
Symptom
Trouble Area
Brake Actuator (Skid Control ECU) Communication Stop Mode
Either condition is met:
  1. "Skid Control (ABS/VSC/TRAC)" is not displayed on "Bus Check".
  2. "Brake Actuator (Skid Control ECU) Communication Stop Mode" in "DTC Combination Table" applies.
  1. Power source or inside master cylinder solenoid (skid control ECU)
  2. Master cylinder solenoid (skid control ECU) branch wire or connector
  3. Master cylinder solenoid (skid control ECU)
  1. For vehicles with a 1GR-FE, 1KD-FTV engine.

WIRING DIAGRAM

C217310E11

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU BRANCH WIRE)

  1. C208652E03
    Disconnect the A7 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A7-11 (CANH) - A7-25 (CANL)
    Ignition switch off
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Master Cylinder Solenoid [Skid Control ECU])



NG
REPAIR OR REPLACE SKID CONTROL ECU BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

  1. C212910E03
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the A8 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A7-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A7-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A8-4 (GND3) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A7-2 (+BM1) - Body ground
    Always
    11 to 14 V
    A8-2 (+BM2) - Body ground
    Always
    11 to 14 V
    A7-31 (+BS) - Body ground
    Always
    11 to 14 V
    A8-1 (IG2) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Master Cylinder Solenoid [Skid Control ECU])


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)


← Brake Actuator (Skid Control ECU) Communication Stop Mode (from Aug 2014)Skid Control ECU Communication Stop Mode (from Aug 2014) →