DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2013
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the intelligent tester, read the Data List.
Driver Seat Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Reclining Rear
Reclining switch signal (Rearward) / ON or OFF
ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off
-
Reclining Front
Reclining switch signal (Forward) / ON or OFF
ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off
-
Front Vertical Down
Front vertical switch signal (Downward) / ON or OFF
ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off
-
Front Vertical Up
Front vertical switch signal (Upward) / ON or OFF
ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off
-
Lifter Switch Down
Lifter switch signal (Downward) / ON or OFF
ON: Lifter switch (Downward) on
OFF: Lifter switch (Downward) off
-
Lifter Switch Up
Lifter switch signal (Upward) / ON or OFF
ON: Lifter switch (Upward) on
OFF: Lifter switch (Upward) off
-
Slide Rear
Sliding switch signal (Rearward) / ON or OFF
ON: Sliding switch (Rearward) on
OFF: Sliding switch (Rearward) off
-
Slide Front
Sliding switch signal (Forward) / ON or OFF
ON: Sliding switch (Forward) on
OFF: Sliding switch (Forward) off
-
Seat Memory No1
Seat position memorized with M1 switch / Mem or Not Mem
Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2
Seat position memorized with M2 switch / Mem or Not Mem
Mem: Memorized
Not Mem: Not memorized
-
Ignition Switch
Communication state of ignition switch signal / ON or OFF
ON: Ignition switch ON signal received
OFF: Ignition switch ON signal not received
-
P Switch
Shift lever position P signal / ON or OFF
ON: Shift lever in P
OFF: Shift lever not in P
-
Parking Brake SW
Parking brake switch status / ON or OFF
ON: Parking brake applied
OFF: Parking brake released
-
Vehicle Speed
Vehicle speed data / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
Actual vehicle speed
-
Power Voltage
Power supply for front power seat switch / min: 0 V, max: 19.89 V
Within range of 11 to 14 V
-
Slide Position
Seat sliding position / min: 0000, max: 65535
Within range of 0 to 65535
-
Reclining Position
Seat reclining position / min: 0000, max: 65535
Within range of 0 to 65535
-
Front Vertical Position
Seat front vertical position / min: 0000, max: 65535
Within range of 0 to 65535
-
Lifter Position
Seat lifter position / min: 0000, max: 65535
Within range of 0 to 65535
-
Slide Pos Mem No1
Seat sliding position memorized with M1 switch / min: 0000, max: 65535
Within range of 0 to 65535
-
Reclining Pos Mem No1
Seat reclining position memorized with M1 switch / min: 0000, max: 65535
Within range of 0 to 65535
-
Frnt Vrtcl Pos Mem No1
Front vertical position memorized with M1 switch / min: 0000, max: 65535
Within range of 0 to 65535
-
Lifter Pos Mem No1
Lifter position memorized with M1 switch / min: 0000, max: 65535
Within range of 0 to 65535
-
Slide Pos Mem No2
Seat sliding position memorized with M2 switch / min: 0000, max: 65535
Within range of 0 to 65535
-
Reclining Pos Mem No2
Seat reclining position memorized with M2 switch / min: 0000, max: 65535
Within range of 0 to 65535
-
Frnt Vrtcl Pos Mem No2
Front vertical position memorized with M2 switch / min: 0000, max: 65535
Within range of 0 to 65535
-
Lifter Pos Mem No2
Lifter position memorized with M2 switch / min: 0000, max: 65535
Within range of 0 to 65535
-
Slide Position Init Flg
Seat sliding limit position memory / ON or OFF
ON: Memorized
OFF: Not memorized
-
Slide Position Rear Limit
Seat sliding position / min: 0000, max: 65535
Within range of 0 to 65535
-
Shift P SW (PMN)
Shift lever position P signal / ON or OFF
ON: Shift lever in P
OFF: Shift lever not in P
-
Memory Button Buzzer Request
Driver seat buzzer request display / OFF, MOVE, REGISTRY, CANCEL, REG NG or REG WAIT
OFF: Buzzer does not sound
MOVE: Request to sound buzzer when starting memory replay
REGISTRY: Request to sound buzzer when starting memory registration
CANCEL: Request to sound buzzer when canceling memory call registration
REG NG: Request to sound buzzer when memory call registration not possible
REG WAIT: Request to sound buzzer when starting memory call cabin scan
-
Driver Seat Request Command
Driver seat operation request received / OFF, MEMORY, MEM MOV, MEM SOD, RET MOV, AWY MOV, AWY SOD, MEM AWY or MEM RET
OFF: No instruction
MEMORY: Request to memorize
MEM MOV: Request to recall memory
MEM SOD: Request to recall through memory call function
RET MOV: Request to return
AWY MOV: Request to move away
AWY SOD: Request to recall away position memory
MEM AWY: Request to recall memorized position of seat
MEM RET: Request to restore seat to memorized position
-
Driver Seat POS REQ
Seat memory switch operation value / OFF, MEM1, MEM2, MEM3, DRV1, DRV2 or DRV3
OFF: No operation
MEM1: M1 switch operation status
MEM2: M2 switch operation status
MEM3: Related switch does not exist
DRV1: Memory call 1 function operating
DRV2: Memory call 2 function operating
DRV3: Related function does not exist
-
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D-Door Courtesy
Front door courtesy light switch assembly signal / ON or OFF
ON: Driver side door open
OFF: Driver side door closed
-
Mem SW No. w/KeyID1
Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2 or MEM SW3
NONE: No switches linked with key ID1
MEM SW1: M1 switch linked with key ID1
MEM SW2: M2 switch linked with key ID1
MEM SW3: Related switch does not exist
-
Mem SW No. w/KeyID2
Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2 or MEM SW3
NONE: No switches linked with key ID2
MEM SW1: M1 switch linked with key ID2
MEM SW2: M2 switch linked with key ID2
MEM SW3: Related switch does not exist
-
Mem SW No. w/KeyID3
Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2 or MEM SW3
NONE: No switches linked with key ID3
MEM SW1: M1 switch linked with key ID3
MEM SW2: M2 switch linked with key ID3
MEM SW3: Related switch does not exist
-
Mem SW No. w/KeyID4
Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2 or MEM SW3
NONE: No switches linked with key ID4
MEM SW1: M1 switch linked with key ID4
MEM SW2: M2 switch linked with key ID4
MEM SW3: Related switch does not exist
-
Mem SW No. w/KeyID5
Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2 or MEM SW3
NONE: No switches linked with key ID5
MEM SW1: M1 switch linked with key ID5
MEM SW2: M2 switch linked with key ID5
MEM SW3: Related switch does not exist
-
Mem SW No. w/KeyID6
Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2 or MEM SW3
NONE: No switches linked with key ID6
MEM SW1: M1 switch linked with key ID6
MEM SW2: M2 switch linked with key ID6
MEM SW3: Related switch does not exist
-
Mem SW No. w/KeyID7
Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2 or MEM SW3
NONE: No switches linked with key ID7
MEM SW1: M1 switch linked with key ID7
MEM SW2: M2 switch linked with key ID7
MEM SW3: Related switch does not exist
-
M1 Switch
Seat memory switch M1 signal / ON or OFF
ON: Seat memory switch M1 on
OFF: Seat memory switch M1 off
-
M2 Switch
Seat memory switch M2 signal / ON or OFF
ON: Seat memory switch M2 on
OFF: Seat memory switch M2 off
-
SET Switch
Seat memory switch SET signal / ON or OFF
ON: Seat memory switch SET on
OFF: Seat memory switch SET off
-
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Driver Seat / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Driver Seat Tester Display
Test Part
Control Range
Diagnostic Note
Seat Reclining
Seat reclining operation
Front / OFF / Rear
-
Front Vertical Operation
Seat front vertical operation
Up / OFF / Down
-
Lifter Operation
Seat lifter operation
Up / OFF / Down
-
Seat Slide Operation
Seat sliding operation
Front / OFF / Rear
-
Buzzer
Buzzer operation
ON / OFF
-