2013-2015 Land Cruiser Prado · Service Manual Steering

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering wheel (Click here).

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE NO. 3 STEERING WHEEL LOWER COVER

  1. B238307
    Detach the 2 claws and remove the cover.


4. REMOVE NO. 2 STEERING WHEEL LOWER COVER

  1. B238308E01
    Detach the 2 claws and remove the cover.
    Text in Illustration 
    *A
    w/o Cruise Control System
    *B
    w/ Cruise Control System


5. REMOVE STEERING PAD

  1. B238309E01
    Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.
    Text in Illustration 
    *1
    Screw Case

  1. B238310
    Pull out the steering pad from the steering wheel as shown in the illustration. Then support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector.

  1. Disconnect the 2 connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


6. REMOVE NO. 1 STEERING WHEEL ORNAMENT

  1. C217183
    Remove the 2 screws.

  1. Detach the claw, 3 guide pins and then remove the ornament.


7. REMOVE NO. 2 STEERING WHEEL ORNAMENT
  1. Remove the 2 screws.

  1. Detach the claw, 3 guide pins and then remove the ornament.

    HINT:
    Refer to "Remove No. 1 Steering Wheel Ornament".


8. REMOVE STEERING PAD SWITCH ASSEMBLY (w/ Steering Pad Switch)
  1. Disconnect the connector.

  1. Remove the 4 screws.

  1. Detach the 2 claws, 6 guide pins and then remove the steering pad switch assembly.

    HINT:
    Refer to "Remove No. 1 Steering Wheel Ornament".


9. REMOVE STEERING PAD SWITCH RH (w/ Steering Pad Switch)
  1. Disconnect the connector.

  1. Remove the 2 screws.

  1. Detach the claw, 3 guide pins and steering pad switch RH.

    HINT:
    Refer to "Remove No. 1 Steering Wheel Ornament".


10. REMOVE CRUISE CONTROL MAIN SWITCH (w/ Cruise Control System)

  1. B239943
    Disconnect the connector.

  1. Remove the 2 screws and switch.


11. REMOVE STEERING WHEEL HEATER CONTROL ASSEMBLY (w/ Steering Heater)

  1. C290119
    Disconnect the 2 connectors and connector clamp.

  1. Remove the 2 screws and steering wheel heater control assembly.


12. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel set nut.

  1. C215868E01
    Put matchmarks on the steering wheel and main shaft.
    Text in Illustration 
    *a
    Matchmark
    *b
    Hold
    *c
    Turn

  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →