2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. INSTALL NO. 1 COOLER THERMISTOR

E197775E01

NOTICE:
If reusing the evaporator, do not insert the sensor into a location where the sensor was previously inserted.

  1. Insert the sensor to a location that is 1 fin to the right or left of its previous location.

    Standard Dimension:
    Area
    Specified Condition
    a
    50 mm (1.97 in.)
    b
    46.7 mm (1.84 in.)
    c
    33.3 mm (1.31 in.)
    d
    154.1 mm (6.07 in.)
    e
    25 mm (0.98 in.)

    Text in Illustration 
    *1
    1 Fin


2. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings to the evaporator.

  1. Install the evaporator.

  1. Attach the 4 claws to install the unit case.

  1. Install the 6 screws.


3. INSTALL DAMPER SERVO SUB-ASSEMBLY LH

  1. Align the grooves on the damper servo sub-assembly with the protrusions on the unit and install the damper servo sub-assembly.

    E197776E01

    Text in Illustration 
    *A
    for Automatic Air conditioning System
    -
    -
    *a
    Air Conditioning Unit Side
    *b
    Damper Servo Side

  1. Install the 4 screws.


4. INSTALL DAMPER SERVO SUB-ASSEMBLY RH

  1. Align the grooves on the damper servo sub-assembly with the protrusions on the unit and install the damper servo sub-assembly.

    E197777E01

    Text in Illustration 
    *a
    Air Conditioning Unit Side
    *b
    Damper Servo Side

  1. Install the 3 screws.


5. INSTALL COOLER EXPANSION VALVE
  1. Install the expansion valve.


6. INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the hose joint.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings to the air conditioner tube and accessory assembly.

  1. Using a 4 mm hexagon wrench, install the 2 bolts.

    Torque:
    3.5 N*m{ 36 kgf*cm , 31 in.*lbf }

  1. Install new butyl tape.

  1. Install new packing.


7. INSTALL AIR CONDITIONING HARNESS
  1. Attach the clamps to install the harness.

  1. Connect the connectors.


8. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
  1. Install the radiator.

  1. Install the 2 brackets with the 2 screws.


9. INSTALL QUICK HEATER ASSEMBLY (w/ PTC Heater)
  1. Attach the 2 clamps to install the quick heater assembly.

  1. Install the 2 screws.


10. INSTALL DRAIN COOLER HOSE

  1. E197396
    install the drain cooler hose.


11. INSTALL ASPIRATOR HOSE
  1. Attach the 2 claws to install the aspirator hose.


12. INSTALL DEFROSTER NOZZLE ASSEMBLY
  1. Attach the 6 claws to install the defroster nozzle assembly.


13. INSTALL BLOWER ASSEMBLY
  1. Attach the 2 claws to install the blower unit assembly.

  1. Install the screw.

    Torque:
    2.7 N*m{ 28 kgf*cm , 24 in.*lbf }

← INSPECTION (from Aug 2013)INSTALLATION (Aug 2013 – Jul 2014) →