2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY LH (for Front Side)

  1. B245520E06
    Disconnect the seat heater control sub-assembly LH (for Front Side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    b7-6 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b7-1 (SWL) - b7-6 (E)
    Ignition switch ON, seat heater switch LH off
    Below 1 V
    Ignition switch ON, seat heater switch LH on
    11 to 14 V
    b7-4 (B) - b7-6 (E)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Seat Heater Control Sub-assembly LH [for Front Side])
    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Connect the seat heater control sub-assembly LH (for Front Side) connector.

  1. B241897E01
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b7-5 (THL) - Body ground
    Ignition switch ON, seat heater switch LH on, MIN → MAX
    Gradual increase between value below 1 V and value from 11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Seat Heater Control Sub-assembly LH [for Front Side])
    If the result is not as specified, the seat seat heater control sub-assembly LH (for Front Side) may have a malfunction.


INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY RH (for Front Side)

  1. B245520E07
    Disconnect the seat heater control sub-assembly RH (for Front Side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    a7-6 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    a7-1 (SWR) - a7-6 (E)
    Ignition switch ON, seat heater switch RH off
    Below 1 V
    Ignition switch ON, seat heater switch RH on
    11 to 14 V
    a7-4 (B1) - a7-6 (E)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Seat Heater Control Sub-assembly RH [for Front Side])
    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Connect the seat heater control sub-assembly RH (for Front Side) connector.

  1. B241897E02
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    a7-5 (THR) - Body ground
    Ignition switch ON, seat heater switch RH on, MIN → MAX
    Gradual increase between value below 1 V and value from 11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Seat Heater Control Sub-assembly RH [for Front Side])
    If the result is not as specified, the seat seat heater control sub-assembly RH (for Front Side) may have a malfunction.


INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY LH (for Rear Side) (w/ Rear Seat Heater System)

  1. B245520E34
    Disconnect the seat heater control sub-assembly LH (for Rear Side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    x1-6 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    x1-1 (SWL) - x1-6 (E)
    Ignition switch ON, seat heater switch LH off
    Below 1 V
    Ignition switch ON, seat heater switch LH on
    11 to 14 V
    x1-4 (B) - x1-6 (E)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Seat Heater Control Sub-assembly LH [for Rear Side])
    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Connect the seat heater control sub-assembly LH (for Rear Side) connector.

  1. B241897E24
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    x1-5 (THL) - Body ground
    Ignition switch ON, seat heater switch LH on, MIN → MAX
    Gradual increase between value below 1 V and value from 11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Seat Heater Control Sub-assembly LH [for Rear Side])
    If the result is not as specified, the seat seat heater control sub-assembly LH (for Rear Side) may have a malfunction.


INSPECT SEAT HEATER CONTROL SUB-ASSEMBLY RH (for Rear Side) (w/ Rear Seat Heater System)

  1. B245520E35
    Disconnect the seat heater control sub-assembly RH (for Rear Side) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    w1-6 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    w1-1 (PWR) - w1-6 (E)
    Ignition switch ON, seat heater switch RH off
    Below 1 V
    Ignition switch ON, seat heater switch RH on
    11 to 14 V
    w1-4 (B) - w1-6 (E)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Seat Heater Control Sub-assembly RH [for Rear Side])
    If the result is not as specified, there may be a malfunction on the wire harness side.

  1. Connect the seat heater control sub-assembly RH (for Rear Side) connector.

  1. B241897E25
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    w1-5 (THR) - Body ground
    Ignition switch ON, seat heater switch RH on, MIN → MAX
    Gradual increase between value below 1 V and value from 11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Seat Heater Control Sub-assembly RH [for Rear Side])
    If the result is not as specified, the seat seat heater control sub-assembly RH (for Rear Side) may have a malfunction.

← TERMINALS OF ECU (from Aug 2013)PARTS LOCATION (from Aug 2013) →