2013-2015 Land Cruiser Prado · Service Manual Steering

INSTALLATION

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL POWER STEERING ECU ASSEMBLY
  1. Attach the 2 claws to install the power steering ECU assembly.


2. INSTALL ECU INTEGRATION BOX RH
  1. Install the ECU integration box RH with the 2 nuts and bolt.

  1. Attach the clamp.

  1. Connect the connectors.


3. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY
  1. Attach the 2 claws to install the No. 2 air duct sub-assembly.

  1. Install the screw.


4. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

B238219E01
  1. Connect each connector.

  1. Attach the 5 clips and claw to install the glove compartment door.

  1. Install the 2 bolts <C> and 2 screws <A> or <B>.

    Text in Illustration 
    *1
    Bolt
    *2
    Screw


5. INSTALL INSTRUMENT PANEL ORNAMENT

  1. for LHD:

    1. Attach the 2 guides to install the instrument panel safety pad.

    2. Install the 2 brackets with the 4 bolts and 2 nuts.

    3. Connect the connectors and attach the clamps and claws.

    4. Install the 2 passenger airbag bolts <G>.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    5. Install the 6 bolts <E> and nut <F>.

    6. Install the front floor carpet.

      B361966E01

      Text in Illustration 
      *1
      Bolt <E>
      *2
      Nut <F>
      *3
      Bolt <G>
      *4
      Guide
      *5
      Bracket
      -
      -

  1. for RHD:

    1. Attach the 2 guides to install the instrument panel safety pad.

    2. Install the 2 brackets with the 4 bolts and 2 nuts.

    3. Connect the connectors and attach the clamps and claws.

    4. Install the 2 passenger airbag bolts <G>.

      Torque:
      20 N*m{ 204 kgf*cm , 15 ft.*lbf }

    5. Install the 6 bolts <E> and nut <F>.

    6. Install the front floor carpet.

      B361859E01

      Text in Illustration 
      *1
      Bolt <E>
      *2
      Nut <F>
      *3
      Bolt <G>
      *4
      Guide
      *5
      Bracket
      -
      -


6. INSTALL INSTRUMENT SIDE PANEL RH
  1. Connect the connector.

  1. Attach the 5 clips, claw and 3 guides to install the instrument side panel.


7. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Attach the 3 clips and 2 guides to install the No. 2 instrument panel under cover.

  1. Install the screw.

    B298555E01

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD


8. INSTALL COWL SIDE TRIM BOARD RH
  1. Attach the clip and claw to install the cowl side trim board RH.

  1. Install the clip.


9. INSTALL DOOR SCUFF PLATE ASSEMBLY RH
  1. Attach the 4 clips, 10 claws and 2 guides to install the door scuff plate assembly RH.


10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


11. CHECK SRS WARNING LIGHT
(Click here)
← REMOVAL (from Aug 2014)INSTALLATION (from Aug 2014) →