C1AED Rear Sensor Communication Malfunction
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
This DTC is stored when there is an open or short circuit in the communication line between the rear sensors and ECU, or when there is a malfunction in a rear sensor.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1AED |
An open or short circuit in the communication line between the rear sensors and ECU or a malfunction in a rear sensor during initialization mode after the engine switch is turned on (IG). |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC (C1AED) |
Clear the DTCs (Click here).
Recheck for DTCs (Click here).
Result Result
Proceed to
No DTC is output
A
DTC C1AED is output
B
|
|
||||
| A | ||
| ||
| 2. CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU - REAR CORNER SENSOR LH) |
Disconnect the I1*1 or G154*2 clearance warning ECU connector.
- *1: for 4 Sensor Type
- *2: for 8 Sensor Type
- *1: for 4 Sensor Type
Disconnect the V5 No. 1 ultrasonic sensor (rear corner sensor LH) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for 4 Sensor Type Tester Connection
Condition
Specified Condition
I1-7 (BOR) - V5-1 (BI)
Always
Below 1 Ω
I1-24 (SOR) - V5-3 (SI)
Always
Below 1 Ω
I1-18 (E2) - V5-5 (EI)
Always
Below 1 Ω
I1-7 (BOR) - Body ground
Always
10 kΩ or higher
I1-24 (SOR) - Body ground
Always
10 kΩ or higher
I1-18 (E2) - Body ground
Always
10 kΩ or higher
for 8 Sensor Type Tester Connection
Condition
Specified Condition
G154-7 (BOR) - V5-1 (BI)
Always
Below 1 Ω
G154-24 (SOR) - V5-3 (SI)
Always
Below 1 Ω
G154-18 (E2) - V5-5 (EI)
Always
Below 1 Ω
G154-7 (BOR) - Body ground
Always
10 kΩ or higher
G154-24 (SOR) - Body ground
Always
10 kΩ or higher
G154-18 (E2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (REAR CORNER SENSOR LH - REAR CENTER SENSOR LH) |
Disconnect the V5 No. 1 ultrasonic sensor (rear corner sensor LH) connector.
Disconnect the V4 No. 1 ultrasonic sensor (rear center sensor LH) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
V5-2 (BO) - V4-1 (BI)
Always
Below 1 Ω
V5-4 (SO) - V4-3 (SI)
Always
Below 1 Ω
V5-6 (EO) - V4-5 (EI)
Always
Below 1 Ω
V5-2 (BO) - Body ground
Always
10 kΩ or higher
V5-4 (SO) - Body ground
Always
10 kΩ or higher
V5-6 (EO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR LH - REAR CENTER SENSOR RH) |
Disconnect the V4 No. 1 ultrasonic sensor (rear center sensor LH) connector.
Disconnect the U4 No. 1 ultrasonic sensor (rear center sensor RH) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
V4-2 (BO) - U4-1 (BI)
Always
Below 1 Ω
V4-4 (SO) - U4-3 (SI)
Always
Below 1 Ω
V4-6 (EO) - U4-5 (EI)
Always
Below 1 Ω
V4-2 (BO) - Body ground
Always
10 kΩ or higher
V4-4 (SO) - Body ground
Always
10 kΩ or higher
V4-6 (EO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (REAR CENTER SENSOR RH - REAR CORNER SENSOR RH) |
Disconnect the U4 No. 1 ultrasonic sensor (rear center sensor RH) connector.
Disconnect the U5 No. 1 ultrasonic sensor (rear corner sensor RH) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
U4-2 (BO) - U5-1 (BI)
Always
Below 1 Ω
U4-4 (SO) - U5-3 (SI)
Always
Below 1 Ω
U4-6 (EO) - U5-5 (EI)
Always
Below 1 Ω
U4-2 (BO) - Body ground
Always
10 kΩ or higher
U4-4 (SO) - Body ground
Always
10 kΩ or higher
U4-6 (EO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. INSPECT NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR LH) |
Remove the No. 1 ultrasonic sensor (rear corner sensor LH) (Click here).
Inspect the No. 1 ultrasonic sensor (rear corner sensor LH) (Click here).
|
|
||||
| OK | |
| 7. INSPECT NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR LH) |
Remove the No. 1 ultrasonic sensor (rear center sensor LH) (Click here).
Inspect the No. 1 ultrasonic sensor (rear center sensor LH) (Click here).
|
|
||||
| OK | |
| 8. INSPECT NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR RH) |
Remove the No. 1 ultrasonic sensor (rear center sensor RH) (Click here).
Inspect the No. 1 ultrasonic sensor (rear center sensor RH) (Click here).
|
|
||||
| OK | |
| 9. REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR RH) |
Replace the No. 1 ultrasonic sensor (rear corner sensor RH) with a normally functioning sensor (Click here).
- HINT:
- All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| NEXT | |
| 10. CHECK FOR DTC (C1AED) |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
No DTC is output
A
DTC C1AED is output
B
|
|
||||
| A | ||
| ||
| 11. REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR LH) |
Replace the No. 1 ultrasonic sensor (rear center sensor LH) with a normally functioning sensor (Click here).
- HINT:
- All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| NEXT | |
| 12. CHECK FOR DTC (C1AED) |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
No DTC is output
A
DTC C1AED is output
B
|
|
||||
| A | ||
| ||
| 13. REPLACE NO. 1 ULTRASONIC SENSOR (REAR CENTER SENSOR RH) |
Replace the No. 1 ultrasonic sensor (rear center sensor RH) with a normally functioning sensor (Click here).
- HINT:
- All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| NEXT | |
| 14. CHECK FOR DTC (C1AED) |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
No DTC is output
A
DTC C1AED is output
B
|
|
||||
| A | ||
| ||
| 15. REPLACE NO. 1 ULTRASONIC SENSOR (REAR CORNER SENSOR LH) |
Replace the No. 1 ultrasonic sensor (rear corner sensor LH) with a normally functioning sensor (Click here).
- HINT:
- All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| NEXT | |
| 16. CHECK FOR DTC (C1AED) |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
No DTC is output
A
DTC C1AED is output
B
|
|
||||
|
|
||||
| A | ||
| ||
