2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

TERMINALS OF ECU

System information · Vehicles built from Aug 2013


CHECK CLEARANCE WARNING ECU
E177737E05
  1. Measure the voltage and resistance and check for pulse signals according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    I1-3 (SPD) - I1-21 (E)
    R - W-B
    Vehicle speed signal
    Ignition switch ON, back sonar or clearance sonar switch on
    Alternating between 1.5 to 4.5 V
    I1-6 (SOR) - I1-22 (E2)
    W - R
    Rear ultrasonic sensor communication signal (Rear clearance sonar sensor)
    Ignition switch ON, back sonar or clearance sonar switch on, shift lever in R
    Pulse generation
    (See waveform 2)
    I1-8 (CSSW) - I1-21 (E)
    V - W-B
    Clearance sonar on/off switch signal
    Back sonar or clearance sonar switch on
    11 to 14 V
    I1-10 (IG) - I1-21 (E)
    L - W-B
    IG signal/IG power source signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    I1-13 (RL) - I1-21 (E)
    R - W-B
    Reverse signal
    Ignition switch ON, shift lever in R
    11 to 14 V
    Ignition switch ON, shift lever not in R
    Below 1 V
    I1-14 (BBZ) - I1-12 (EF)
    GR - LG
    No. 1 clearance warning buzzer signal
    Buzzer not sounding
    Below 1 V
    When sonar detects obstacle (buzzer sounds)
    Pulse generation
    (See waveform 1)
    I1-15 (L1) - I1-21 (E)
    LG - W-B
    Clearance warning ECU signal
    Clearance warning indicator LED for rear right sensor illuminates
    Below 3 V
    I1-17 (L3) - I1-21 (E)
    L - W-B
    Ultrasonic sensor (rear center right and left sensor)
    Clearance warning indicator LED for rear left sensor illuminates
    Below 3 V
    I1-19 (L5) - I1-21 (E)
    P - W-B
    Ultrasonic sensor (rear left sensor)
    Clearance warning indicator LED for back sensor illuminates
    Below 3 V
    I1-20 (L6) - I1-21 (E)
    R - W-B
    Ultrasonic sensor (rear right sensor)
    Clearance warning indicator's operation indicator illuminates
    Below 3 V
    I1-21 (E) - Body ground
    W-B - Body ground
    ECU ground
    Always
    Below 1 Ω
    I1-22 (E2) - I1-21 (E)
    R - W-B
    ECU ground
    Always
    Below 1 Ω
    I1-24 (BOR) - I1-22 (E2)
    P - R
    Rear ultrasonic sensor circuit power source
    Ignition switch off
    Below 1.5 V
    Ignition switch ON, back sonar or clearance sonar switch on
    7.2 to 8.8 V

  2. E051095E01
    Using an oscilloscope, check waveform 1.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    I1-14 (BBZ) - I1-12 (EF)
    Tool Setting
    2 V/DIV., 500 μsec./DIV.
    Condition
    When sonar detects obstacle (buzzer sounds)

  3. E159890E01
    Using an oscilloscope, check waveform 2.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    I1-6 (SOR) - I1-22 (E2)
    Tool Setting
    5 V/DIV., 1 msec./DIV.
    Condition
    Ignition switch ON, back sonar or clearance sonar switch on, shift lever in R

← PROBLEM SYMPTOMS TABLE (from Aug 2014)Park / Neutral Position Switch Circuit (Aug 2013 – Jul 2014) →