2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

OPERATION CHECK

Troubleshooting · Vehicles built from Aug 2013


CHECK INITIAL CHECK FUNCTION

  1. E107404E13
    Check the initial check function for the buzzer.

    1. When the back sonar or clearance sonar switch is turned on, check that the following occurs: 1) after 0.4 seconds, the buzzer sounds for approximately 0.7 to 1.3 seconds, and 2) the system starts the obstacle detection operation.

  2. Check the initial check function for the sensor.

    1. Approximately 0.4 seconds after the ignition switch is turned to ON and the back sonar or clearance sonar switch is turned on, all the sensors are checked by the system.
    2. When the shift lever is operated, the system starts the obstacle detection operation.

  3. If a sensor is found to have an anomaly due to an open circuit, the buzzer sounds after the initial check function is completed to inform the driver and indicate which sensor is abnormal.

    1. When the ECU determines that the sensor needs to be repaired or cleaned:
      C159323E03

    2. When the ECU determines that the sensor needs to be cleaned:
      C159324E03

      HINT:
      If the clearance sonar switch is on and the ignition switch is turned to ON, the buzzer does not sound.


DETECTION RANGE MEASUREMENT AND INDICATOR CHECK

CAUTION:
Apply the parking brake securely so that the vehicle does not move.

  1. Turn the ignition switch to ON.

  2. Turn the back sonar or clearance sonar switch on.

  3. Move the shift lever to R to check the rear corner sensors and rear center sensors.

  4. Move a pole around the sensor to measure the detection range of the sensor.

    NOTICE:
    1. These detection ranges are applicable when positioning a pole with a diameter of 60 mm (2.36 in.) parallel or perpendicular to the ground.
    2. The ranges vary depending on the measuring method and type of obstacle (such as walls).
    3. For close-range and medium-range detection, the values shown are for when using a pole with a diameter of 60 mm (2.36 in.). For long-range detection, the values shown are for when using walls.
    4. The No. 1 ultrasonic sensor side view detection range hatched area*1 represents the cross section of the top view of the detection range along the lines labeled A. The hatched area*1 does not represent the entire side view detection range.


    1. Rear corner sensor detection range
      E194322E01

    2. Rear center sensor detection range
      E194323E02

  5. When the ultrasonic sensors have detected an obstacle, check that the buzzer sounds with the back sonar or clearance sonar switch on.

    Operation Condition 
    Shift Lever Position
    Buzzer Operation
    Back LH
    Back RH
    Rear Corner LH
    Rear Corner RH
    R
    Sounds
    Sounds

    1. Check that the buzzer sounds with the back sonar or clearance sonar switch on.
      E132045E07

      Rear Corner Detection Range 
      Detection
      Distance
      1. Close-range detection
      Within 250 +/-30 mm (9.84 +/-1.18 in.)
      2. Medium-range detection
      250 +/-30 to 375 +/-40 mm (9.84 +/-1.18 to 14.8 +/-1.57 in.)
      3. Long-range detection
      375 +/-40 to 550 +/-60 mm (14.8 +/-1.57 to 21.7 +/-2.36 in.)
      Rear Center Detection Range 
      Detection
      Distance
      1. Close-range detection
      Within 400 +/-40 mm (15.7 +/-1.57 in.)
      2. Medium-range detection
      400 +/-40 to 500 +/-50 mm (15.7 +/-1.57 to 19.7 +/-1.97 in.)
      3. Long-range detection
      500 +/-50 to 650 +/-70 mm (19.7 +/-1.97 to 25.6 +/-2.76 in.)
      4. Maximum long-range detection
      650 +/-70 to 1500 +/-150 mm (25.6 +/-2.76 to 59.1+/-5.91 in.)

      HINT:
      Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.

    2. Check the indicator and buzzer when the rear center sensors and rear corner sensors have detected an obstacle.

      Operation Condition 
      Ignition Switch
      Back Sonar or Clearance Sonar Switch
      Shift Lever Position
      ON
      On
      R
      Buzzer 
      Detection Range
      Buzzer
      1. Close-range detection
      Sounds continuously
      2. Medium-range detection
      Sounds intermittently
      (On: 75 msec./Off: 75 msec.)
      3. Long-range detection
      Sounds intermittently
      (On: 150 msec./Off: 150 msec.)
      4. Maximum long-range detection
      Sounds intermittently
      (On: 150 msec./Off: 650 msec.)
      Clearance Warning Indicator 
      Detection Range
      Indicator Displayed
      1. Close-range detection
      Corner indicator(s) are illuminated and/or back indicator is illuminated
      2. Medium-range detection
      Corner indicator(s) are blinking and/or back indicator is blinking
      3. Long-range detection
      Corner indicator(s) are blinking and/or back indicator is blinking
      4. Maximum long-range detection
      Back indicator is blinking
      E194315E01
      Text in Illustration 
      *1
      Clearance warning indicator
      -
      -
      *a
      Corner indicator
      *b
      Back indicator

      HINT:
      Ultrasonic waves are used to measure the detection range. However, the detection range may vary depending on the ambient temperature.

← HOW TO PROCEED WITH TROUBLESHOOTING (from Aug 2014)PROBLEM SYMPTOMS TABLE (Aug 2013 – Jul 2014) →