B27A1 Open in Driver Side Electrical Antenna Circuit
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The certification ECU generates a request signal and transmits the signal to the front door outside handle assembly (for driver side) at an interval of 250 ms. The front door outside handle assembly (for driver side) detects when the electrical key is brought close to the vehicle, and when a request signal is received from within 1.0 m (3.28 ft.) of the driver door, the signal is transmitted at an interval of 250 ms. DTC B27A1 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and front door outside handle assembly (for driver side) (CLG1 - ANT1, CG1B - ANT2).| DTC Code |
DTC Detection Condition |
Trouble Area |
| B27A1 |
An open circuit is detected in the circuit between the certification ECU and front door outside handle assembly (for driver side) (CLG1 - ANT1, CG1B - ANT2). |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
- When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
- Before replacing the certification ECU, refer to the Service Bulletin.
- The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
| 1. CHECK CONNECTOR CONNECTION |
Turn the engine switch off.
Check that the connectors are properly connected to the certification ECU and front door outside handle assembly (for driver side).
- OK:
- Connectors are properly connected.
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU) |
Disconnect the O1*1 or N1*2 handle connector.
- *1: for LHD
- *2: for RHD
- *1: for LHD
Disconnect the G38 ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
O1-3 (ANT2) - G38-4 (CG1B)
Always
Below 1 Ω
O1-6 (ANT1) - G38-3 (CLG1)
Always
Below 1 Ω
O1-2 (GND) - Body ground
Always
Below 1 Ω
G38-4 (CG1B) - Body ground
Always
10 kΩ or higher
G38-3 (CLG1) - Body ground
Always
10 kΩ or higher
G38-15 (E) - Body ground
Always
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
N1-3 (ANT2) - G38-4 (CG1B)
Always
Below 1 Ω
N1-6 (ANT1) - G38-3 (CLG1)
Always
Below 1 Ω
N1-2 (GND) - Body ground
Always
Below 1 Ω
G38-4 (CG1B) - Body ground
Always
10 kΩ or higher
G38-3 (CLG1) - Body ground
Always
10 kΩ or higher
G38-15 (E) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK CERTIFICATION ECU |
Measure the voltage according to the value(s) in the table below.


Text in Illustration *a
Component with harness connected
(Certification ECU)
-
-
- OK:
Tester Connection
Switch Condition
Specified Condition
G38-3 (CLG1) - G38-15 (E)
Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
No pulse generation → Pulse generation
G38-4 (CG1B) - G38-15 (E)
Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
No pulse generation → Pulse generation
|
|
||||
| OK | |
| 4. REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE) |
Temporarily replace the front door outside handle assembly (for driver side) with a new or normally functioning one (Click here).
| NEXT | |
| 5. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC B27A1 is not output.
|
|
||||
| OK | ||
| ||
