2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B27A2 Open in Front Passenger Side Electrical Antenna Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The certification ECU generates a request signal and transmits the signal to the front door outside handle assembly (for front passenger side) at an interval of 250 ms. The front door outside handle assembly (for front passenger side) detects when the electrical key is brought close to the vehicle, and when a request signal is received from within 1.0 m (3.28 ft.) of the front passenger door, the signal is transmitted at an interval of 250 ms. DTC B27A2 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and front door outside handle assembly (for front passenger side) (CLG2 - ANT1, CG2B - ANT2).
DTC Code
DTC Detection Condition
Trouble Area
B27A2
An open circuit is detected in the circuit between the certification ECU and front door outside handle assembly (for front passenger side) (CLG2 - ANT1, CG2B - ANT2).
  1. Harness or connector
  2. Front door outside handle assembly (for front passenger side)
  3. Certification ECU

WIRING DIAGRAM

B243939E02

INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Before replacing the certification ECU, refer to the Service Bulletin.


1. CHECK CONNECTOR CONNECTION
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the certification ECU and front door outside handle assembly (for front passenger side).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
  1. Disconnect the N1*1 or O1*2 handle connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect the G38 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    N1-3 (ANT2) - G38-6 (CG2B)
    Always
    Below 1 Ω
    N1-6 (ANT1) - G38-5 (CLG2)
    Always
    Below 1 Ω
    N1-2 (GND) - Body ground
    Always
    Below 1 Ω
    G38-6 (CG2B) - Body ground
    Always
    10 kΩ or higher
    G38-5 (CLG2) - Body ground
    Always
    10 kΩ or higher
    G38-15 (E) - Body ground
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    O1-3 (ANT2) - G38-6 (CG2B)
    Always
    Below 1 Ω
    O1-6 (ANT1) - G38-5 (CLG2)
    Always
    Below 1 Ω
    O1-2 (GND) - Body ground
    Always
    Below 1 Ω
    G38-6 (CG2B) - Body ground
    Always
    10 kΩ or higher
    G38-5 (CLG2) - Body ground
    Always
    10 kΩ or higher
    G38-15 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK CERTIFICATION ECU

  1. Measure the voltage according to the value(s) in the table below.B224125E16

    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU)
    -
    -

    OK:
    Tester Connection
    Switch Condition
    Specified Condition
    G38-5 (CLG2) - G38-15 (E)
    Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
    No pulse generation → Pulse generation
    G38-6 (CG2B) - G38-15 (E)
    Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed
    No pulse generation → Pulse generation



NG
REPLACE CERTIFICATION ECU
OK


4. REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER SIDE)
  1. Temporarily replace the front door outside handle assembly (for front passenger side) with a new or normally functioning one (Click here).


NEXT


5. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B27A2 is not output.



NG
REPLACE CERTIFICATION ECU
OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY IS DEFECTIVE)


← B27A2 Open in Front Passenger Side Electrical Antenna Circuit (Aug 2013 – Jul 2014)B27A5 Open in Front Floor Electrical Key Oscillator Circuit (Aug 2013 – Jul 2014) →