2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

B27A7 Open in Inside Luggage Compartment Electrical Key Oscillator Circuit

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The certification ECU generates a request signal and transmits the signal to the indoor No. 3 electrical key antenna (inside luggage). The indoor No. 3 electrical key antenna (inside luggage) detects that the electrical key is inside the vehicle and transmits the request signal received from the certification ECU. DTC B27A7 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and indoor No. 3 electrical key antenna (inside luggage) (CLG7 - CLG6, CG7B - CLGB).
DTC Code
DTC Detection Condition
Trouble Area
B27A7
An open circuit is detected in the circuit between the certification ECU and indoor No. 3 electrical key antenna (inside luggage) (CLG7 - CLG6, CG7B - CLGB).
  1. Harness or connector
  2. Indoor No. 3 electrical key antenna (inside luggage)
  3. Certification ECU

WIRING DIAGRAM

B210705E15

INSPECTION PROCEDURE

NOTICE:
  1. The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
  3. Before replacing the certification ECU, refer to the Service Bulletin.


1. CHECK CONNECTOR CONNECTION
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the certification ECU and indoor No. 3 electrical key antenna (inside luggage).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2. CHECK HARNESS AND CONNECTOR (INDOOR NO. 3 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
  1. Disconnect the R15 antenna connector.

  1. Disconnect the G38 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R15-1 (CLG6) - G38-26 (CLG7)
    Always
    Below 1 Ω
    R15-2 (CLGB) - G38-27 (CG7B)
    Always
    Below 1 Ω
    G38-26 (CLG7) - Body ground
    Always
    10 kΩ or higher
    G38-27 (CG7B) - Body ground
    Always
    10 kΩ or higher
    G38-15 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK CERTIFICATION ECU

  1. Measure the voltage according to the value(s) in the table below.B224125E19

    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU)
    -
    -

    OK:
    Tester Connection
    Switch Condition
    Specified Condition
    G38-26 (CLG7) - G38-15 (E)
    Engine switch off, all doors closed, key not in cabin and lock sensor off → on
    No pulse generation → Pulse generation
    G38-27 (CG7B) - G38-15 (E)
    Engine switch off, all doors closed, key not in cabin and lock sensor off → on
    No pulse generation → Pulse generation



NG
REPLACE CERTIFICATION ECU
OK


4. REPLACE INDOOR NO. 3 ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)
  1. Temporarily replace the indoor No. 3 electrical key antenna (inside luggage) with a new or normally functioning one (Click here).


NEXT


5. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B27A7 is not output.



NG
REPLACE CERTIFICATION ECU
OK

END (INDOOR NO. 3 ELECTRICAL KEY ANTENNA ASSEMBLY IS DEFECTIVE)


← B27A6 Open in Rear Floor Electrical Key Oscillator Circuit (from Aug 2014)B27A7 Open in Inside Luggage Compartment Electrical Key Oscillator Circuit (from Aug 2014) →