2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE DOOR SCUFF PLATE ASSEMBLY LH
  1. for 5 Door:
    Remove the door scuff plate assembly LH (Click here).

  1. for 3 Door:
    Remove the door scuff plate assembly LH (Click here).


3. REMOVE COWL SIDE TRIM BOARD LH
  1. for 5 Door:
    Remove the cowl side trim board LH (Click here).

  1. for 3 Door:
    Remove the cowl side trim board LH (Click here).


4. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

B356218
  1. for LHD:

    1. Remove the screw.

    2. Detach the 2 clips and 2 guides and remove the No. 1 instrument panel under cover.

    3. Disconnect each connector.

  1. B298554
    for RHD:

    1. Remove the screw.

    2. Detach the 3 clips and 2 guides and remove the No. 1 instrument panel under cover.

    3. Disconnect each connector.


5. REMOVE INSTRUMENT SIDE PANEL LH

B238205E01
  1. Put protective tape around the instrument side panel.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel.


6. REMOVE INSTRUMENT CLUSTER FINISH PANEL ORNAMENT (for LHD)

B238207E01
  1. Put protective tape around the instrument cluster finish panel ornament.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 3 clips and remove the instrument cluster finish panel ornament.


7. REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for RHD)

B238239
  1. Detach the 4 clips.

  1. Disconnect each connector and remove the instrument panel finish plate garnish.


8. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

B238214
  1. Detach the 4 clips.

  1. Disconnect each connector and remove the instrument panel finish panel.


9. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

B239280E01
  1. Using a screwdriver, detach the 2 claws and open the cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. B243715
    w/o Knee Airbag:

    1. Remove the 2 bolts <C>.

    2. Detach the 7 clips.

    3. Disconnect each connector and each cable and remove the lower instrument panel finish panel.

  1. B238216
    w/ Knee Airbag:

    1. Remove the 2 bolts <C>.

    2. Detach the 14 clips.

    3. Disconnect each connector and each cable and remove the lower instrument panel finish panel.


10. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

  1. B238327
    Remove the 4 bolts and airbag assembly.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


11. REMOVE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

  1. E197200
    Disconnect the 3 connectors.

  1. E197201E06
    Detach the 2 claws and disconnect the 2 connectors labeled (1) as shown in the illustration.

  1. Disconnect the connector labeled (2).

  1. E197202
    Remove the bolt and 2 nuts and disconnect the driver side junction block assembly.

  1. E178377
    Detach the claw and disconnect the connector as shown in the illustration.

  1. E178379
    Detach the 2 claws and release the connector's lock as shown in the illustration.

  1. E178381
    Detach the claw and disconnect the connector as shown in the illustration.

  1. Remove the driver side junction block assembly.


12. REMOVE MULTIPLEX NETWORK BODY ECU

  1. E183106E01
    Press the claw of the junction block as shown in the illustration to release the lock.
    Text in Illustration 
    *1
    Multiplex Network Body ECU
    *2
    Driver Side Junction Block
    *3
    Protective Tape

  1. With the junction block lock released, insert a screwdriver with its tip wrapped with protective tape horizontally between the multiplex network body ECU and junction block.

    NOTICE:
    Use a screwdriver with a radius of between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).

  1. E183107
    Using the screwdriver, carefully raise the multiplex network body ECU until the connector becomes disengaged.

    NOTICE:
    Do not twist the screwdriver to raise the multiplex network body ECU.

  1. B195950E01
    Raise the multiplex network body ECU as shown by arrow (1), and then pull it out as shown by arrow (2) in the illustration.

    NOTICE:
    Do not touch the ECU connector.

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →