2013-2015 Land Cruiser Prado · Service Manual Vehicle Exterior

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/ Rain Sensor)

  1. for LHD Windshield Wiper Switch and RHD Windshield Wiper Switch RH Side Type:

    1. E182610E03
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Rear Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      12 (C1R) - 1 (EW)
      OFF
      10 kΩ or higher
      10 (+1R) - 1 (EW)
      12 (C1R) - 1 (EW)
      LO
      Below 1 Ω
      10 (+1R) - 1 (EW)
      HI
      Below 1 Ω
      Rear Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      11 (WR) - 1 (EW)
      OFF
      10 kΩ or higher
      10 (+1R) - 1 (EW)
      11 (WR) - 1 (EW)
      WASH
      Below 1 Ω
      11 (WR) - 1 (EW)
      ON + WASH
      Below 1 Ω
      10 (+1R) - 1 (EW)

      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)
      If the result is not as specified, replace the windshield wiper switch assembly.

  1. for RHD Windshield Wiper Switch LH Side Type:

    1. E182610E04
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Rear Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      16 (C1R) - 9 (EW)
      OFF
      10 kΩ or higher
      18 (+1R) - 9 (EW)
      16 (C1R) - 9 (EW)
      LO
      Below 1 Ω
      18 (+1R) - 9 (EW)
      HI
      Below 1 Ω
      Rear Washer Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      17 (WR) - 9 (EW)
      OFF
      10 kΩ or higher
      18 (+1R) - 9 (EW)
      17 (WR) - 9 (EW)
      WASH
      Below 1 Ω
      17 (WR) - 9 (EW)
      ON + WASH
      Below 1 Ω
      18 (+1R) - 9 (EW)

      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)
      If the result is not as specified, replace the windshield wiper switch assembly.


INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/o Rain Sensor)

  1. for LHD Windshield Wiper Switch and RHD Windshield Wiper Switch RH Side Type:

    1. E171721E19
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      A-1 (+S) - A-3 (+1)
      OFF
      Below 1 Ω
      INT
      A-2 (+B) - A-3 (+1)
      MIST
      LO
      A-2 (+B) - A-4 (+2)
      HI
      Front Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      B-2 (EW) - B-3 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher
      Rear Wiper Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      B-6 (C1R) - B-2 (EW)
      OFF
      10 kΩ or higher
      B-7 (+1R) - B-2 (EW)
      B-6 (C1R) - B-2 (EW)
      INT
      Below 1 Ω
      B-7 (+1R) - B-2 (EW)
      HI
      Below 1 Ω
      Rear Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      A-5 (WR) - B-2 (EW)
      OFF
      10 kΩ or higher
      B-7 (+1R) - B-2 (EW)
      A-5 (WR) - B-2 (EW)
      WASH
      Below 1 Ω
      A-5 (WR) - B-2 (EW)
      ON + WASH
      Below 1 Ω
      B-7 (+1R) - B-2 (EW)

      If the result is not as specified, replace the windshield wiper switch assembly.
      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)

    2. Check the intermittent operation.

      1. Connect the positive (+) lead of a voltmeter to terminal A-3 (+1) and the negative (-) lead to terminal B-2 (EW).
      2. Connect the battery positive (+) lead of the battery to terminal A-2 (+B) and the negative (-) lead to terminal B-2 (EW) and A-1 (+S).
      3. Turn the wiper switch to the INT position.
      4. Connect the positive (+) lead of the battery to terminal A-1 (+S) for 5 seconds.

      5. Connect the negative (-) lead of the battery to terminal A-1 (+S). Operate the intermittent wiper relay and check the voltage between terminals A-3 (+1) and B-2 (EW).

        OK:
        The voltage changes as shown in the illustration.


        E056399E59
        If the result is not as specified, replace the windshield wiper switch assembly.
        Text in Illustration 
        *1
        Voltage between terminals A-3 (+1) and B-2 (EW)
        *2
        Voltage between terminals A-3 (+1) and B-2 (EW)
        *3
        Voltage between terminals A-3 (+1) and B-2 (EW)
        -
        -

  1. for RHD Windshield Wiper Switch LH Side Type:

    1. E202530E01
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch 
      Tester Connection
      Switch Condition
      Specified Condition
      A-4 (+S) - A-2 (+1)
      OFF
      Below 1 Ω
      INT
      A-3 (+B) - A-2 (+1)
      MIST
      LO
      A-3 (+B) - A-1 (+2)
      HI
      Front Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      B-2 (EW) - B-1 (WF)
      ON
      Below 1 Ω
      OFF
      10 kΩ or higher
      Rear Wiper Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      B-5 (C1R) - B-2 (EW)
      OFF
      10 kΩ or higher
      B-4 (+1R) - B-2 (EW)
      B-5 (C1R) - B-2 (EW)
      INT
      Below 1 Ω
      B-4 (+1R) - B-2 (EW)
      HI
      Below 1 Ω
      Rear Washer Switch:
      Tester Connection
      Switch Condition
      Specified Condition
      A-10 (WR) - B-2 (EW)
      OFF
      10 kΩ or higher
      B-4 (+1R) - B-2 (EW)
      A-10 (WR) - B-2 (EW)
      WASH
      Below 1 Ω
      A-10 (WR) - B-2 (EW)
      ON + WASH
      Below 1 Ω
      B-4 (+1R) - B-2 (EW)

      If the result is not as specified, replace the windshield wiper switch assembly.
      Text in Illustration 
      *a
      Component without harness connected
      (Windshield Wiper Switch Assembly)

    2. Check the intermittent operation.

      1. Connect the positive (+) lead of a voltmeter to terminal A-2 (+1) and the negative (-) lead to terminal B-2 (EW).
      2. Connect the positive (+) lead of the battery to terminal A-3 (+B) and the negative (-) lead to terminal B-2 (EW) and A-4 (+S).
      3. Turn the wiper switch to the INT position.
      4. Connect the positive (+) lead of the battery to terminal A-4 (+S) for 5 seconds.

      5. Connect the negative (-) lead of the battery to terminal A-4 (+S). Operate the intermittent wiper relay and check the voltage between terminals A-2 (+1) and B-2 (EW).

        OK:
        The voltage changes as shown in the illustration.


        E056399E59
        If the result is not as specified, replace the windshield wiper switch assembly.
        Text in Illustration 
        *1
        Voltage between terminals A-2 (+1) and B-2 (EW)
        *2
        Voltage between terminals A-2 (+1) and B-2 (EW)
        *3
        SLOW: Connect battery negative lead to terminal A-4 (+S)
        -
        -

← REMOVAL (from Aug 2014)INSTALLATION (Aug 2013 – Jul 2014) →