2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

C1622 Open or Short Circuit in Back Camera Signal

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored if the navigation receiver assembly judges as a result of its self check that the signals or signal lines between the navigation receiver assembly and the rear television camera assembly are not normal.
DTC Code
DTC Detection Condition
Trouble Area
C1622
Open or Short Circuit in television camera signal
  1. Harness or connector
  2. Rear television camera assembly
  3. Navigation receiver assembly

WIRING DIAGRAM

E286150E02

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC is output
    B



B
Go to step 2
A

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the H62 navigation receiver assembly connector.

  1. Disconnect the v2 rear television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H62-7 (CA+) - v2-6 (CB+)
    Always
    Below 1 Ω
    H62-8 (V+) - v2-3 (CV+)
    Always
    Below 1 Ω
    H62-15 (CGND) - v2-5 (CGND)
    Always
    Below 1 Ω
    H62-16 (V-) - v2-2 (CV-)
    Always
    Below 1 Ω
    H62-7 (CA+) - Body ground
    Always
    10 kΩ or higher
    H62-8 (V+) - Body ground
    Always
    10 kΩ or higher
    H62-15 (CGND) - Body ground
    Always
    10 kΩ or higher
    H62-16 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK NAVIGATION RECEIVER ASSEMBLY

  1. E280620E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    H62-15 (CGND) - Body ground
    Always
    Below 1 Ω
    H62-16 (V-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H62-7 (CA+) - H62-15 (CGND)
    Engine switch on (ACC)
    5.5 to 7.05 V

Text in Illustration 
*a
Component with harness connected
(Navigation Receiver Assembly)


NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


4. CHECK REAR TELEVISION CAMERA ASSEMBLY

  1. Using an oscilloscope, check the waveform.E224537E14

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)
    *b
    Waveform 1
    *c
    Waveform 2
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -
    Measurement Condition 
    Item
    Content
    Tester Connection
    H62-8 (V+) - H62-15 (CGND)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    1. Waveform 1: Engine switch on (IG)
    2. Waveform 2: Engine switch on (IG), screen blacked out by covering camera lens

    OK:
    Waveform is as shown in illustration.

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.



NG
Go to step 5
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

5. REPLACE REAR TELEVISION CAMERA ASSEMBLY
  1. Replace the rear television camera assembly with a new or normally functioning one (Click here).


NEXT


6. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (REAR TELEVISION CAMERA ASSEMBLY WAS DEFECTIVE)


← C1622 Open or Short Circuit in Back Camera Signal (Aug 2013 – Jul 2014)C1625 Open or Short in Steering Angle Sensor +B (Aug 2013 – Jul 2014) →