2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

U1114 Lost Communication with Main Switch Module

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

DTC Code
DTC Detection Condition
Trouble Area
U1114
There is no communication from the driving support switch control ECU.
  1. Power source circuit of driving support switch control ECU
  2. Driving support switch control ECU CAN branch wire or connector
  3. Driving support switch control ECU
  1. For vehicles with a multi-function switch.

WIRING DIAGRAM

C294454E03

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR OPEN IN CAN BUS WIRE (DRIVING SUPPORT SWITCH CONTROL ECU CAN BRANCH WIRE)

  1. for Automatic Transmission:

    1. C289482E01
      Disconnect the G163 driving support switch control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      G163-2 (CANP) - G163-3 (CANN)
      Ignition switch off
      54 to 69 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Driving Support Switch Control ECU)

  1. for Manual Transmission:

    1. C215998E01
      Disconnect the G76 driving support switch control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      G76-9 (CANP) - G76-10 (CANN)
      Ignition switch off
      54 to 69 Ω

      Text in Illustration 
      *a
      Rear view of wire harness connector
      (to Driving Support Switch Control ECU)



NG
REPAIR OR REPLACE DRIVING SUPPORT SWITCH CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)
OK


3. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - BATTERY AND BODY GROUND)
  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. for Automatic Transmission:

    1. C289482E02
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      G163-7 (GND) - Body ground
      Always
      Below 1 Ω

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      G163-8 (+B) - Body ground
      Always
      11 to 14 V
      G163-10 (IG) - Body ground
      Ignition switch ON
      11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Driving Support Switch Control ECU)

  1. for Manual Transmission:

    1. C215998E02
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      G76-16 (GND) - Body ground
      Always
      Below 1 Ω

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      G76-6 (+B) - Body ground
      Always
      11 to 14 V
      G76-7 (IG) - Body ground
      Ignition switch ON
      11 to 14 V

Text in Illustration 
*a
Rear view of wire harness connector
(to Driving Support Switch Control ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU (Click here)


← U1110 Lost Communication with Clearance Sonar Module (from Aug 2014)U1114 Lost Communication with Main Switch Module (from Aug 2014) →