DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2013
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: All ECUs / (desired system) / Data List.
According to the display on the intelligent tester, read the Data List.
Pre-Crash Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Driver Buckle SW
Driver side buckle switch status of driver side seat / UNKNOW, UNSET, SET or NG
UNKNOW: Driver side buckle switch status unknown
UNSET: Driver side seat belt unfastened
SET: Driver side seat belt fastened
NG: Indeterminate data
-
Passenger Buckle SW
Front passenger side buckle switch status of passenger side seat / UNKNOW, UNSET, SET or NG
UNKNOW: Passenger side buckle switch status unknown
UNSET: Passenger side seat belt unfastened
SET: Passenger side seat belt fastened
NG: Indeterminate data
-
Driver Belt Control
Seat belt control status of driver side seat / STOP, ON or ERROR
STOP: Control stopped
ON: Controlled
ERROR: Indeterminate data
The seat belt (driver side) is fastened.
Passenger Belt Control
Seat belt control status of passenger side seat / STOP, ON or ERROR
STOP: Control stopped
ON: Controlled
ERROR: Indeterminate data
The seat belt (passenger side) is fastened.
Number of Trouble Codes
Number of stored trouble codes / Min.: 0, Max.: 255
Number of stored DTCs displayed
-
Pre-Crash 2 Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Wiper Information
Wiper information signal / Unoperat, Oil off, Mist, Washer, Unknown, Intermi, Lo or Hi
Unoperat: Windshield wiper switch off
Oil off: Oil filter clearing operation
Mist: Windshield wiper switch MIST
Washer: Windshield wiper switch WASHER
Intermi: Windshield wiper switch INT
Lo: Windshield wiper switch Lo
Hi: Windshield wiper switch Hi Unknown: Wiper information signal unknown
-
Pre-Crash Brake OFF Switch
Pre-crash brake cancel switch assembly signal / ON or OFF
ON: Pre-crash brake cancel switch assembly on
OFF: Pre-crash brake cancel switch assembly off
-
Pre-Crash System
Pre-crash safety system signal / Valid or Inval
Valid: Pre-crash safety system operation possible
Inval: Pre-crash safety system operation not possible
-
DCam Indicator
Driver camera indicator display request signal / ON or OFF
ON: Driver camera indicator display requested
OFF: Driver camera indicator display not requested
-
PCS Indicator
PCS indicator light signal / ON or OFF
ON: PCS indicator light blinks
OFF: PCS indicator light off
-
PCS Disabled Indicator
Pre-crash safety system disabled indicator signal / ON or OFF
ON: Pre-crash safety system disabled indicator on
OFF: Pre-crash safety system disabled indicator off
-
Pre-Crash Safety Warning Ind
Pre-crash safety warning indicator light signal / ON or OFF
ON: Pre-crash safety warning indicator light blinks
OFF: Pre-crash safety warning indicator light off
-
Pre-Crash Safety Brake Ind
Pre-crash safety brake indicator light signal / ON or OFF
ON: Pre-crash safety brake indicator light on
OFF: Pre-crash safety brake indicator light off
-
Pre-Crash Safety Warning Buz
Pre-crash safety warning buzzer signal / Valid or Inval
Valid: Pre-crash safety warning buzzer operation possible
Inval: Pre-crash safety warning buzzer operation not possible
-
Pre-Crash Brake
Pre-crash brake signal / Valid or Inval
Valid: Pre-crash brake operation possible
Inval: Pre-crash brake operation not possible
-
Front Radar PSB
Pre-crash seat belt signal / ON or OFF
ON: Pre-crash seat belt operating
OFF: Pre-crash seat belt not operating
-
PBA Start
Pre-crash brake assist operation signal / ON or OFF
ON: Pre-crash brake assist brake operating
OFF: Pre-crash brake assist brake not operating
-
Warning Brake
Warning brake control signal / ON or OFF
ON: Warning brake control operating
OFF: Warning brake control not operating
-
Back Assist Standby
Brake assist standby signal / ON or OFF
ON: Brake assist in standby mode
OFF: Brake assist not in standby mode
-
Pre-Crash Brake Control
Pre-crash brake control signal / ON or OFF
ON: Pre-crash brake control operating
OFF: Pre-crash brake control not operating
-
AVS Start
AVS control activation status / ON or OFF
ON: AVS control activated
OFF: AVS control not activated
-
CCS Cancel
Dynamic radar cruise control system cancel signal / ON or OFF
ON: Dynamic radar cruise control system canceled
OFF: Dynamic radar cruise control system operating
-
Front Radar-Dirt History
Millimeter wave radar sensor dirty signal / ON or OFF
ON: Millimeter wave radar sensor dirty
OFF: Millimeter wave radar sensor not dirty
-
Front Radar-Environment Hist
Millimeter wave radar sensor environment signal / Good or Bad
Good: Millimeter wave radar sensor environment good
Bad: Millimeter wave radar sensor environment bad
-
Curr Com PCS-WIL-R
Front active headrest ECU RH connection status / without or with
with: Front active headrest ECU RH connected
without: Front active headrest ECU RH not connected
-
Curr Com PCS-WIL-L
Front active headrest ECU LH connection status / without or with
with: Front active headrest ECU LH connected
without: Front active headrest ECU LH not connected
-
Curr Com Night View ECU
Night view ECU connection status / without or with
with: Night view ECU connected
without: Night view ECU not connected
-
Country# (DSS)
Driving support ECU country signal / JPN, NA, EURO, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC or NOFIX
EURO, AUS, TWN, THAI or GCC
-
The Number of DTCs
Number of stored trouble codes / Min.: 0, Max.: 255
Number of stored DTCs displayed
-
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Pre-Crash Tester Display
Test Part
Control Range
Diagnostic Note
Driver Seat Belt Motor
Driver side seat belt motor
ON/OFF
The seat belt (driver side) is fastened.
Passenger Seat Belt Motor
Passenger side seat belt motor
ON/OFF
The seat belt (passenger side) is fastened.
Driver and Passenger Seat Belt Motor
Driver and passenger side seat belt motor
ON/OFF
The seat belts (driver and passenger side) are fastened.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
Buzzer
Skid control buzzer
ON/OFF
-
Combination Meter Tester Display
Test Part
Control Range
Diagnostic Note
Indicat. Precrash
PCS indicator light
ON/OFF
-