2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System)
  1. Remove the electric EGR control valve assembly (Click here).


3. DISCONNECT INLET HEATER WATER HOSE (w/o EGR System)

  1. A224418
    Remove the bolt and disconnect the inlet heater water hose.


4. DISCONNECT NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/o EGR System)

  1. A222558
    Remove the bolt and disconnect the No. 4 vacuum transmitting pipe.


5. REMOVE NO. 1 INTAKE PIPE (w/o EGR System)

  1. A222559
    Disconnect the 3 connectors from the intake air temperature sensor, throttle control motor and manifold absolute pressure sensor.

  1. Detach the 2 clamps.

  1. Disconnect the vacuum hose from the manifold absolute pressure sensor.

  1. A222560
    Loosen the 2 hose clamps of the No. 1 air hose.

  1. A222561
    Loosen the hose clamp of the intercooler air hose.

  1. A222562
    Remove the 2 bolts and No. 1 intake pipe.


6. REMOVE THROTTLE BODY BRACKET (w/o EGR System)

  1. A230166
    Disconnect the vacuum hose.

  1. Remove the bolt and gas filter with gas filter bracket.

  1. Remove the 2 bolts and throttle body bracket.


7. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/o EGR System)

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating the injector inlet.

  1. A223449
    Remove the 2 nuts and No. 3 injection pipe clamp.

  1. A225331
    Remove the 2 bolts and 2 No. 2 injection pipe clamps.

  1. A223451E01
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
    Text in Illustration 
    *a
    for Injector Side
    *b
    for Common Rail Side


8. REMOVE AIR CONNECTOR STAY (w/o EGR System)

  1. A230167
    Remove the 3 bolts and air connector stay.


9. DISCONNECT ENGINE WIRE (w/o EGR System)

  1. A225769
    for LHD:
    Remove the 2 bolts and disconnect the clamp and engine wire.

  1. A225770
    for RHD:
    Remove the bolt and disconnect the engine wire.


10. REMOVE INTAKE AIR CONNECTOR WITH DIESEL THROTTLE BODY ASSEMBLY (w/o EGR System)

  1. A230087
    Disconnect the throttle position sensor connector.

  1. A230165
    Remove the 3 bolts, intake air connector with diesel throttle and gasket.


11. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE

  1. Disconnect the vacuum switching valve connector.

    1. A222570
      w/o EGR System:
      Disconnect the connector.

    2. A222575
      w/ EGR System without EGR Cooler:
      Disconnect the 2 connectors.

    3. A222581
      w/ EGR System with EGR Cooler:
      Disconnect the 3 connectors.

  1. A224689
    Disconnect the No. 1 vacuum transmitting hose.

  1. A224691
    w/ EGR System:
    Disconnect the No. 2 vacuum transmitting hose and No. 3 vacuum transmitting hose.

  1. A224690
    w/ EGR Cooler:
    Disconnect the No. 3 vacuum transmitting hose.

  1. A224718E03
    Disconnect the No. 3 vacuum transmitting hose and No. 4 vacuum transmitting hose.
    Text in Illustration 
    *A
    w/o EGR System
    *B
    w/ EGR System

  1. A222572
    Remove the 2 bolts and manifold stay with vacuum switching valve.


12. REMOVE INTAKE PIPE OR HOSE STAY

  1. A220705
    Remove the bolt and intake pipe stay.


13. REMOVE VACUUM CONTROL VALVE SET

  1. A152488
    Disconnect the 2 VSV connectors and 3 vacuum hoses.

  1. Remove the 2 bolts and vacuum control valve set.


14. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

  1. A152275
    Remove the bolt and detach the injection pipe clamp.

    NOTICE:
    If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.

  1. A152276E06
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
    Text in Illustration 
    *a
    Injector Side
    *b
    Common Rail Side


15. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

  1. A152742E01
    Disconnect the 3 fuel hoses.

  1. Remove the union bolt, 4 bolts, No. 2 nozzle leakage pipe and gasket.

    Text in Illustration 
    *1
    Union Bolt


16. REMOVE INTAKE MANIFOLD INSULATOR

  1. A152712
    Remove the 2 bolts and intake manifold insulator.


17. REMOVE INTAKE MANIFOLD

  1. A223283E01
    Detach the sensor wire connector clamp from the intake manifold.
    Text in Illustration 
    *1
    Sensor Wire

  1. A220706
    Disconnect the vacuum hose from the intake manifold.

  1. Remove the 2 nuts, 4 bolts, intake manifold and gasket.

← COMPONENTS (from Aug 2013)REMOVAL (from Aug 2014) →