DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2013
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Entire the following menus: Powertrain / Radar Cruise / Data List.
According to the display on the intelligent tester, read the Data List.
Radar Cruise Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Accel Request
Dynamic radar cruise acceleration value / Min.: -2621.44 km/h/s, Max.: 2621.36 km/h/s
Requested acceleration value
-
Vehicle Distance
Vehicle distance / Min.: 0 m, Max.: 6553.5 m*1 or 255 m*2
Actual vehicle distance
-
L/C Option Flag
Dynamic radar cruise option flag / No or Yes
No: Dynamic radar cruise control system cannot be used
Yes: Dynamic radar cruise control system can be used
-
Car Dist Time Setting
Vehicle distance setting / Mid, Shrt, No or Long
Mid: Vehicle distance setting middle
Shrt: Vehicle distance setting short
No: Vehicle-to-vehicle distance control mode not operating
Long: Vehicle distance setting long
-
O/D Cut Request
Overdrive cut request signal / Not Request or Request
Not Request: Overdrive cut not operating
Request: Overdrive cut operating
-
Shift Down Rqst to 3rd
Shift down request signal / Not Request or Request
Not Request: No shift down request signal received
Request: Shift down request signal received
-
Shift Down Rqst to 4th
Shift down request signal / Not Request or Request
Not Request: No shift down request signal received
Request: Shift down request signal received
-
Alarm Request
Skid control buzzer request signal / Not Request or Request
Not Request: Skid control buzzer does not sound
Request: Skid control buzzer sounds
-
All Throttle Close Rqst
Throttle close request signal / Not Request or Request
Not Request: No throttle close request signal received
Request: Throttle close request signal received
-
Brake Control Request
Brake control request signal / Not Request or Request
Not Request: No brake control request signal received
Request: Brake control request signal received
-
Targ Decl Slope
Cruise target deceleration slope / 0.03, 0.06, 0.11, 0.15
Actual target deceleration slope
-
CCS Vehicle Spd
Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph)
Actual vehicle speed displayed
-
CCS Mem Vehicle Spd
Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (159 mph)
Vehicle speed stored in memory
-
Throttle Opening Angle*1
Required throttle opening amount / Min.: 0°, Max.: 124.5°
Required throttle opening amount
-
Throttle Opening Angle*2
Required throttle opening amount / Min.: 0%, Max.: 100%
Required throttle opening amount
-
Cruise Control
Cruise control system operation signal / ON or OFF
ON: Cruise control system operating
OFF: Cruise control system not operating
-
Main SW M-CPU
Cruise control switch (Main CPU) signal / ON or OFF
ON: Cruise control switch on
OFF: Cruise control switch off
-
CCS Ready M-CPU
Cruise control standby condition (Main CPU) / ON or OFF
ON: Cruise control switch on
OFF: Cruise control switch off
-
CCS Indicator M-CPU
CRUISE main indicator (Main CPU) / ON or OFF
ON: CRUISE main indicator light on
OFF: CRUISE main indicator light off
-
Cancel Switch
Cancel switch signal / ON or OFF
ON: Cancel switch on
OFF: Cancel switch off
-
SET/COAST Switch
-SET switch signal / ON or OFF
ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch
+RES switch signal / ON or OFF
ON: +RES switch on
OFF: +RES switch off
-
Stp Light SW M-CPU
Stop light switch (Main CPU) signal / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Cruise Operation Status
Shift lever position signal / ON or OFF
ON: Shift lever in D
OFF: Shift lever not in D
-
- *1: for 1GR-FE
- *2: for 1KD-FTV
- *1: for 1GR-FE
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Entire the following menus: Body / (desired system) / Active Test.
According to the display on the intelligent tester, perform the Active Test.
Combination Meter Tester Display
Test Part
Control Range
Diagnostic Note
Indicat. Radar Cruise
Cruise control indicator light
ON/OFF
-
Indicat. SET
Cruise control SET indicator light
ON/OFF
-
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
Buzzer
Skid control buzzer
ON/OFF
-