2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

B2661 Lost Communication with Combination Meter

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This DTC is stored when LIN communication between the driving support switch control ECU and combination meter assembly stops 10 seconds or more.
DTC Code
DTC Detection Condition
Trouble Area
B2661
No communication between the driving support switch control ECU and combination meter assembly for 10 seconds or more.
  1. Driving support switch control ECU
  2. Combination meter assembly
  3. Harness or connector

WIRING DIAGRAM

C217632E32

INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the ignition switch off to troubleshoot:
    Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
  2. Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B2661 is not output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK

3. CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT SWITCH CONTROL ECU - COMBINATION METER)
  1. for Manual Transmission

    1. Disconnect the G76 driving support switch control ECU connector.

    2. Disconnect the G6 combination meter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      G76-5 (LIN) - G6-37 (LIN)
      Always
      Below 1 Ω
      G76-5 (LIN) or G6-37 (LIN) - Body ground
      Always
      10 kΩ or higher

  1. for Automatic Transmission

    1. Disconnect the G162 driving support switch control ECU connector.

    2. Disconnect the G6 combination meter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      G162-16 (LIN) - G6-37 (LIN)
      Always
      Below 1 Ω
      G162-16 (LIN) or G6-37 (LIN) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - BATTERY AND BODY GROUND)

  1. E200096E11
    Disconnect the G6 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G6-21 (E2) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G6-26 (B) - Body ground
    Always
    11 to 14 V
    G6-28 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Combination Meter Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE COMBINATION METER ASSEMBLY
  1. Temporarily replace the combination meter assembly with a new or normally functioning one (Click here).


NEXT


6. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7. CHECK FOR DTC
  1. Check for DTCs (Click here).



NG
REPLACE DRIVING SUPPORT SWITCH CONTROL ECU (Click here)
OK

END (COMBINATION METER IS DEFECTIVE)


← B2661 Lost Communication with Combination Meter (Aug 2013 – Jul 2014)B2785 Communication Malfunction between ECUs Connected by LIN (Aug 2013 – Jul 2014) →