INSTALLATION
Removal / installation · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
| 1. INSTALL NO. 1 FUEL TANK CUSHION |
Install 2 new No. 1 fuel tank cushions to the fuel tank.
| 2. INSTALL FUEL TUBE GROMMET |
Attach the clamp to install the fuel tube grommet.
| 3. INSTALL FUEL TANK FILLER PIPE LOWER SUB-ASSEMBLY |
Install a new gasket and the fuel tank filler pipe lower with the 8 screws.
- Torque:
- 3.0 N*m{ 31 kgf*cm , 27 in.*lbf }
| 4. INSTALL FUEL TANK BREATHER HOSE |
Install the fuel tank breather hose to the fuel tank.
| 5. INSTALL FUEL TANK TO FILLER PIPE HOSE |
Install the fuel tank to filler pipe hose to the fuel tank.
| 6. INSTALL FUEL SENDER GAUGE ASSEMBLY |
Install a new gasket and the fuel sender gauge with the 5 screws.
- Torque:
- 1.5 N*m{ 15 kgf*cm , 13 in.*lbf }
- NOTICE:
- Be careful not to bend the arm of the fuel sender gauge.
| 7. INSTALL FUEL CUT OFF VALVE ASSEMBLY |
Install the fuel cut off valve to the fuel tank.
| 8. INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY |
Install a new gasket and the No. 1 fuel evaporation tube with the 4 screws.
- Torque:
- 1.5 N*m{ 15 kgf*cm , 13 in.*lbf }
| 9. INSTALL FUEL TANK VENT TUBE SUB-ASSEMBLY |
Install a new gasket and the fuel tank vent tube with the 7 screws and attach the 2 clamps.
- Torque:
- 3.5 N*m{ 36 kgf*cm , 31 in.*lbf }
| 10. INSTALL FUEL TANK CHECK VALVE |
Connect the hose and install the fuel tank check valve.
| 11. INSTALL NO. 4 FUEL TUBE CLAMP |
Install the No. 4 fuel tube clamp to the fuel tank check valve and attach the clamp.
| 12. INSTALL FUEL TANK SUB-ASSEMBLY |
Set the fuel tank on a transmission jack and lift up the transmission jack.
Install the 2 fuel tank bands with the 2 pins and 2 clips.
Connect the 2 fuel tank bands with the 2 bolts.
- Torque:
- 40 N*m{ 408 kgf*cm , 30 ft.*lbf }
| 13. CONNECT FUEL TANK BREATHER HOSE |
Connect the fuel tank breather hose to the filler pipe.
| 14. CONNECT FUEL TANK TO FILLER PIPE HOSE |
Connect the fuel tank to filler pipe hose to the filler pipe.
| 15. CONNECT FUEL HOSE |
Connect the 2 fuel hoses.
| 16. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY |
Install the No. 1 fuel tank protector with the 5 bolts.
- Torque:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
| 17. INSTALL REAR FLOOR SERVICE HOLE COVER |
Connect the fuel sender gauge connector and fuel tank ground connector.
Install the rear floor service hole cover with the 3 screws.
| 18. INSTALL REAR FLOOR MAT SUPPORT PLATE |
Attach the 6 claws to install the rear floor mat rear support plate.
Install the 5 screws.
| 19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 20. BLEED AIR FROM FUEL SYSTEM |
- w/ DPF (Click here)
- w/o DPF (Click here)
| 21. INSPECT FOR FUEL LEAK |
- w/ DPF (Click here)
- w/o DPF (Click here)
