2013-2015 Land Cruiser Prado · Service Manual Brake

C1282 Center Differential Lock Position Switch

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

DTC C1282 is stored only in test mode.
DTC Code
DTC Detection Condition
Trouble Area
C1282
Stored during test mode.
  1. Harness or connector
  2. Transfer system
  3. Brake actuator assembly (Skid control ECU)

WIRING DIAGRAM

C212546E07

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform calibration (Click here).


1. INSPECT CENTER DIFFERENTIAL LOCK SHIFT
  1. Check that the center differential can shift from free to lock, and from lock to free.

    OK:
    The center differential can shift from free to lock, and from lock to free.



NG
Go to step 3
OK


2. CHECK TEST MODE DTC
  1. Switch the vehicle to test mode, perform the center differential lock signal check, and then check that DTC C1282 is cleared (Click here).

    Result 
    Result
    Proceed to
    DTC is not cleared
    A
    DTC is cleared
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

3. CHECK TERMINAL VOLTAGE (EXI4)
  1. Set the vehicle in the center differential locked state using the center differential lock switch.

  1. Disconnect the A6 skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. C199357E09
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A6-9 (EXI4) - Body ground
    Center differential locked
    (Center differential lock switch on)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)

  1. Connect the A6 skid control ECU connector.

  1. Set the vehicle in the center differential free state using the center differential lock switch.

  1. Disconnect the A6 skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A6-9 (EXI4) - Body ground
    Center differential free
    (Center differential lock switch off)
    11 to 14 V



NG
Go to step 5
OK


4. CHECK TEST MODE DTC
  1. Switch the vehicle to test mode, perform the center differential lock signal check, and then check that DTC C1282 is cleared (Click here).

    Result 
    Result
    Proceed to
    DTC is not cleared
    A
    DTC is cleared
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FOUR WHEEL DRIVE CONTROL ECU/TRANSFER SHIFT ACTUATOR)
  1. Disconnect the A6 skid control ECU connector.

  1. Disconnect the G53 four wheel drive control ECU connector.

  1. Disconnect the C43 transfer shift actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A6-9 (EXI4) - G53-14 (P1)
    Always
    Below 1 Ω
    A6-9 (EXI4) - C43-9 (CDL)
    Always
    Below 1 Ω
    A6-9 (EXI4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO TRANSFER SYSTEM (PROBLEM SYMPTOMS TABLE) (Click here)


← C1268 Transfer L4 Position Switch Circuit (from Aug 2014)C1282 Center Differential Lock Position Switch (from Aug 2014) →