2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

B238105E01
  1. Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the handle.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


2. REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side)

B238107
  1. Remove the screw and handle.


3. REMOVE FRONT SEAT CUSHION SHIELD LH

  1. B238108
    Remove the screw.

  1. Using a moulding remover, detach the 4 claws and clip, and then remove the cushion shield.

  1. B239165
    for Driver Side:
    Detach the 5 wire harness clamps and disconnect the 2 connectors.


4. REMOVE LUMBAR SWITCH ASSEMBLY (for Driver Side)

B239166
  1. Remove the 2 screws and switch.


5. REMOVE FRONT SEAT INNER CUSHION SHIELD LH

B239167
  1. Using a moulding remover, detach the 3 claws and remove the cushion shield.


6. REMOVE FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)

B239169
  1. Using a moulding remover, detach the 4 claws and remove the cushion shield.


7. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
  1. for Driver Side:
    (Click here)

  1. for Front Passenger Side:
    (Click here)


8. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

  1. B239173
    Remove the rubber band from the seat cushion spring.

  1. B241809
    for Driver Side:
    Detach the clamp and disconnect the No. 2 seat wire.

  1. B241810
    w/ Seat Heater System:
    Disconnect the seat heater connector and detach the wire harness clamp.

  1. B239176
    for Clip Type:
    Using a clip remover, remove the 2 clips.

  1. B239177
    for Hook Type:
    Detach the 2 hooks.

  1. B239174E01
    w/ Front Seat Side Airbag:

    1. Detach the claw and disconnect the airbag connector.

    2. Detach the 3 airbag wire harness clamps.

    3. Detach the fastening tape and open the cover.

      Text in Illustration 
      *1
      Fastening Tape

    4. Disconnect the airbag wire harness.

  1. B239178
    Remove the 4 bolts and seatback assembly.


9. REMOVE CAP

B239170
  1. Remove the 2 caps.


10. REMOVE FRONT SEAT LEG COVER LH

B239171
  1. Detach the 2 claws.

  1. Move the cover in the direction of the arrow to remove it.


11. REMOVE SEAT CUSHION COVER WITH PAD

  1. B241811
    w/ Seat Heater System:
    Disconnect the seat heater connector and detach the 3 wire harness clamps.

  1. Detach the hooks.

    B239180

  1. B239181
    for Front Passenger Side:
    Detach the claw and disconnect the connector.

  1. Remove the seat cushion cover with pad.


12. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER

  1. B372264
    Type A:

    1. Remove the hog rings and disconnect the straps.

  1. B372267E01
    Type B:

    1. Cut off the tack pins and disconnect the straps.

      Text in Illustration 
      *1
      Tack Pin

  1. B239182
    Remove the hog rings and seat cushion cover from the seat cushion pad.


13. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

B239184E01
  1. Cut off the tack pins and remove the front seat cushion heater from the front seat cushion cover.

    Text in Illustration 
    *1
    Tack Pin


14. REMOVE RECLINING ADJUSTER INSIDE COVER LH

B239186
  1. Detach the claw and guide, and then remove the cover.


15. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH

B239187
  1. Remove the screw.

  1. Detach the hook and clip, and then remove the cushion shield.


16. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH
  1. Remove the screw.

  1. Detach the hook and clip, and then remove the cushion shield.


17. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR LH

B239188
  1. Remove the screw.

  1. Move the protector in the direction of the arrow to detach the hook and remove the protector.


18. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR RH

HINT:
Use the same procedure described for the LH side.


19. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

B239190
  1. Disconnect the connector.

  1. Detach the 2 clamps and remove the seat heater control.


20. REMOVE FRONT SEAT WIRE LH
  1. Remove the seat wire.


21. REMOVE RECLINING ADJUSTER INSIDE COVER LH

B239256
  1. Detach the guide.

  1. Move the cover in the direction of the arrow to remove it.


22. REMOVE RECLINING ADJUSTER INSIDE COVER RH

HINT:
Use the same procedure described for the LH side.


23. REMOVE SEPARATE TYPE FRONT SEATBACK COVER

  1. B239192
    Remove the 3 hog rings.

  1. Open the 2 fasteners, and then open the seatback cover.

    B242232E01

    Text in Illustration 
    *A
    for Cloth Seat
    *B
    for Leather Seat

  1. B239201
    w/ Front Seat Side Airbag:

    1. Remove the nut and seatback cover bracket from the seat frame.

    2. Disconnect the seatback cover bracket from the seatback pad.

  1. B239198
    Using a screwdriver, detach the 4 claws and remove the 2 headrest supports.

  1. Remove the hog rings and seatback cover.

    HINT:
    The number of hog rings differs according to seat type.


    B242230E01
    Text in Illustration 
    *A
    for Type A
    *B
    for Type B


24. REMOVE FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)

B239207E01
  1. Cut off the tack pins which fasten the seatback heater to the seatback cover, and then remove the seatback heater from the seatback cover.

    Text in Illustration 
    *1
    Tack Pin


25. REMOVE SEPARATE TYPE FRONT SEATBACK PAD
  1. Remove the seatback pad.


26. REMOVE NO. 2 SEAT WIRE (for Driver Side)

B239209
  1. Disconnect the connector.

  1. Detach the 2 clamps and remove the seat wire.


27. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)

CAUTION:
When storing the front seat side airbag assembly, keep the airbag deployment side facing upward.

HINT:
Use the same procedure for the RH and LH sides.

  1. B251815
    Detach the 2 clamps.

  1. B333276
    Remove the 2 nuts and front seat side airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.

← DISASSEMBLY (Aug 2013 – Jul 2014)INSPECTION (from Aug 2013) →