REASSEMBLY
Removal / installation · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
- Use the same procedure for RHD and LHD vehicles.
| 1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag) |
- CAUTION:
- The nuts must not be reused.
- Make sure that the separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.
- The nuts must not be reused.
- HINT:
- Use the same procedure for the RH and LH sides.
Install the front seat side airbag assembly with 2 new nuts.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
Attach the 2 clamps.
| 2. INSTALL NO. 2 SEAT WIRE (for Driver Side) |
Attach the 2 clamps to install the seat wire.
Connect the connector.
| 3. INSTALL SEPARATE TYPE FRONT SEATBACK PAD |
Install the seatback pad.
| 4. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System) |
![]() ![]() |
Set the seatback heater with the name stamp side facing the seatback cover.
Text in Illustration *1
Tack Pin
*2
Seatback Cover
*3
Seatback Heater
*4
Name Stamp
Install the seatback heater with new tack pins.
| 5. INSTALL SEPARATE TYPE FRONT SEATBACK COVER |
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
- Be careful not to damage the cover.
- HINT:
- The number of hog rings differs according to seat type.


Text in Illustration *A
for Type A
*B
for Type B
*1
Hog Ring Pliers
-
-
Attach the 4 claws to install the 2 headrest supports.
w/ Front Seat Side Airbag:

Connect the seatback cover bracket to the seatback pad.
Install the seatback cover bracket to the seat frame with the nut.
- Torque:
- 5.5 N*m{ 56 kgf*cm , 49 in.*lbf }
- NOTICE:
- After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
Close the 2 fasteners, and then close the seatback cover.


Text in Illustration *A
for Cloth Seat
*B
for Leather Seat
Using hog ring pliers, install 3 new hog rings.

Text in Illustration *1
Hog Ring Pliers
| 6. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
![]() ![]() |
Move the cover in the direction of the arrow to install the cover.
Attach the guide.
| 7. INSTALL RECLINING ADJUSTER INSIDE COVER RH |
- HINT:
- Use the same procedure described for the LH side.
| 8. INSTALL FRONT SEAT WIRE LH |
Install the seat wire.
| 9. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System) |
Attach the 2 clamps to install the seat heater control.
Connect the connector.
| 10. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH |
![]() ![]() |
Move the protector in the direction of the arrow to attach the hook and install the protector.
Install the screw.
| 11. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH |
- HINT:
- Use the same procedure described for the LH side.
| 12. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH |
Attach the hook and clip to install the cushion shield.
Install the screw.
| 13. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH |
Attach the hook and clip to install the cushion shield.
Install the screw.
| 14. INSTALL RECLINING ADJUSTER INSIDE COVER LH |
Attach the claw and guide to install the cover.
| 15. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System) |
![]() ![]() |
Set the seat cushion heater with the name stamp side facing the seat cushion cover.
Text in Illustration *1
Tack Pin
*2
Seatback Cover
*3
Seatback Heater
*4
Name Stamp
Install the seat cushion heater with new tack pins.
| 16. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER |
![]() ![]() |
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
Text in Illustration *1
Hog Ring Pliers
- NOTICE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
- Be careful not to damage the cover.
Type A:

Using hog ring pliers, connect the straps with new hog rings.
Text in Illustration *1
Hog Ring Pliers
Type B:

Connect the straps with new tack pins.
Text in Illustration *1
Tack Pin
| 17. INSTALL SEAT CUSHION COVER WITH PAD |
Install the seat cushion cover with pad.
for Front Passenger Side:
Attach the claw to connect the connector.
Attach the hooks.
w/ Seat Heater System:
Connect the seat heater connector and attach the 3 wire harness clamps.
| 18. INSTALL FRONT SEAT LEG COVER LH |
![]() ![]() |
Move the cover in the direction of the arrow to install the cover.
Attach the 2 claws.
| 19. INSTALL CAP |
Install the 2 caps.
| 20. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY |
Install the seatback assembly with the 4 bolts.
- Torque:
- 42 N*m{ 428 kgf*cm , 31 ft.*lbf }
w/ Front Seat Side Airbag:
Connect the airbag wire harness.
Attach the fastening tape to close the cover.
Attach the 3 airbag wire harness clamps.
Attach the claw and connect the airbag connector.
for Clip Type:
Install the 2 clips.
for Hook Type:
Attach the 2 hooks.
w/ Seat Heater System:
Connect the seat heater connector and attach the wire harness clamp.
for Driver Side:
Attach the clamp to connect the No. 2 seat wire.
Install the rubber band to the seat cushion spring.
| 21. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH |
for Driver Side:
(Click here)
for Front Passenger Side:
(Click here)
| 22. INSTALL FRONT SEAT INNER CUSHION SHIELD LH |
![]() ![]() |
Attach the 3 claws to install the cushion shield.
| 23. INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side) |
Attach the 4 claws to install the cushion shield.
| 24. INSTALL LUMBAR SWITCH ASSEMBLY (for Driver Side) |
Install the switch with the 2 screws.
| 25. INSTALL FRONT SEAT CUSHION SHIELD LH |
for Driver Side:
Attach the 5 wire harness clamps and connect the 2 connectors.
Attach the 4 claws and clip to install the cushion shield.

Install the screw.
| 26. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side) |
Install the handle with the screw.
| 27. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH |
![]() ![]() |
Attach the claw to install the handle.








