2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH

B239185E01
  1. Set the seat cushion heater with the name stamp side facing the seat cushion cover.

    Text in Illustration 
    *1
    Tack Pin
    *2
    Seatback Cover
    *3
    Seatback Heater
    *4
    Name Stamp

  1. Install the seat cushion heater with new tack pins.


2. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

B239183E01
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B372265E01
    Type A:

    1. Using hog ring pliers, connect the straps with new hog rings.

      Text in Illustration 
      *1
      Hog Ring Pliers

  1. B372267E01
    Type B:

    1. Connect the straps with new tack pins.

      Text in Illustration 
      *1
      Tack Pin


3. INSTALL SEAT CUSHION COVER WITH PAD
  1. Install the seat cushion cover with pad.

  1. for Front Passenger Side:
    Attach the claw to connect the connector.

  1. Attach the hooks.

  1. Connect the seat heater connector and attach the 3 wire harness clamps.

  1. for Clip Type:
    Install the 2 clips.

  1. for Hook Type:
    Attach the 2 hooks.

  1. w/ Front Seat Side Airbag:

    1. Connect the airbag wire harness.

    2. Attach the fastening tape to close the cover.

  1. Connect the seat heater connector and attach the wire harness clamp.

  1. Install the rubber band to the seat cushion spring.


4. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH
  1. for Driver Side:
    (Click here)

  1. for Front Passenger Side:
    (Click here)


5. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

B239168
  1. Attach the 3 claws to install the cushion shield.


6. INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)
  1. Attach the 4 claws to install the cushion shield.


7. INSTALL FRONT SEAT CUSHION SHIELD LH
  1. for Driver Side:
    Attach the 5 wire harness clamps and connect the 2 connectors.

  1. B239164
    Attach the 4 claws and clip to install the cushion shield.

  1. Install the screw.


8. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)
  1. Install the handle with the screw.


9. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

B238106
  1. Attach the claw to install the handle.


10. INSTALL FRONT SEAT ASSEMBLY
  1. Install the front seat assembly (Click here).

← INSTALLATION (Aug 2013 – Jul 2014)COMPONENTS (Aug 2013 – Jul 2014) →