2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. REMOVE FRONT SEAT ASSEMBLY
  1. Remove the front seat assembly (Click here).


2. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

B238105E01
  1. Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the handle.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


3. REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side)

B238107
  1. Remove the screw and handle.


4. REMOVE FRONT SEAT CUSHION SHIELD LH

  1. B238108
    Remove the screw.

  1. Using a moulding remover, detach the 4 claws and clip, and then remove the cushion shield.

  1. B239165
    for Driver Side:
    Detach the 5 wire harness clamps and disconnect the 2 connectors.


5. REMOVE FRONT SEAT INNER CUSHION SHIELD LH

B239167
  1. Using a moulding remover, detach the 3 claws and remove the cushion shield.


6. REMOVE FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)

B239169
  1. Using a moulding remover, detach the 4 claws and remove the cushion shield.


7. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
  1. for Driver Side:
    (Click here)

  1. for Front Passenger Side:
    (Click here)


8. REMOVE SEAT CUSHION COVER WITH PAD

  1. B239173
    Remove the rubber band from the seat cushion spring.

  1. B241810
    Disconnect the seat heater connector and detach the wire harness clamp.

  1. B241812E01
    w/ Front Seat Side Airbag:

    1. Detach the fastening tape and open the cover.

      Text in Illustration 
      *1
      Fastening Tape

    2. Disconnect the airbag wire harness.

  1. B239176
    for Clip Type:
    Using a moulding remover, remove the 2 clips.

  1. B239177
    for Hook Type:
    Detach the 2 hooks.

  1. B241811
    Disconnect the seat heater connector and detach the 3 wire harness clamps.

  1. Detach the hooks.

    B239180

  1. B239181
    for Front Passenger Side:
    Detach the claw and disconnect the connector.

  1. Remove the seat cushion cover with pad.


9. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER

  1. B372264
    Type A:

    1. Remove the hog rings and disconnect the straps.

  1. B372267E01
    Type B:

    1. Cut off the tack pins and disconnect the straps.

      Text in Illustration 
      *1
      Tack Pin

  1. B239182
    Remove the hog rings and seat cushion cover from the seat cushion pad.


10. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY LH

B239184E01
  1. Cut off the tack pins and remove the front seat cushion heater from the front seat cushion cover.

    Text in Illustration 
    *1
    Tack Pin

← COMPONENTS (from Aug 2014)REMOVAL (from Aug 2014) →