2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. REMOVE REAR SEAT UPPER RECLINING COVER RH

B237712E01
  1. Using a screwdriver, detach the 3 claws and remove the rear seat upper reclining cover RH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


2. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

B237713
  1. Remove the 3 screws and reclining adjuster release handle RH.


3. REMOVE REAR SEAT CUSHION MOULDING RH

B237716
  1. Using a clip remover, detach the clip.

  1. Using a moulding remover, detach the 3 claws.

  1. Move the rear seat cushion moulding RH in the direction of the arrow to detach the guide and remove the rear seat cushion moulding RH.


4. REMOVE REAR SEAT REAR CUSHION MOULDING LH

B237799
  1. Remove the screw.

  1. Using a moulding remover, detach the 3 claws.

  1. Detach the 2 guides and remove the rear seat rear cushion moulding LH.


5. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH

B241730E01
  1. Remove the bolt and inner belt.


6. REMOVE REAR SEAT INNER BELT ASSEMBLY

B241739
  1. Remove the nut and inner belt.


7. REMOVE REAR SEATBACK LOCK STRIKER COVER RH

B237718
  1. Using a clip remover, detach the 3 clips and remove the rear seatback lock striker cover RH.


8. REMOVE SEAT CUSHION COVER WITH PAD

  1. B359311
    w/ Seat Heater System:

    1. Disconnect the 2 rear seat heater connectors.

    2. B360129
      Pull out the wire harness as shown in the illustration.

  1. B237909
    Detach the hooks and remove the seat cushion cover with pad.


9. REMOVE REAR NO. 2 SEAT PROTECTOR

B237723
  1. Remove the 2 rear No. 2 seat protectors from the separate type rear seat cushion pad.


10. REMOVE REAR SEAT CUSHION EDGE PROTECTOR
  1. Remove the rear seat cushion edge protector from the cushion spring.


11. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER

B237911
  1. Remove the 14 hog rings and separate type rear seat cushion cover from the separate type rear seat cushion pad.


12. REMOVE REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

B248328E01
  1. Cut off the 23 tack pins and remove the rear seat cushion heater assembly from the separate type rear seat cushion cover.

    Text in Illustration 
    *1
    Tack Pin


13. REMOVE RECLINING ADJUSTER KNOB CAP RH

  1. B237754E01
    Using a screwdriver, detach the claw and guide, and then remove the reclining adjuster knob cap RH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


14. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH

  1. B237756
    Remove the 2 screws.

  1. B165052E02
    Disconnect the cable in the order shown in the illustration and remove the rear seat lock control lever sub-assembly RH.


15. REMOVE REAR SEAT COVER CAP

B237913
  1. Using a screwdriver, detach the claw and guide, and then remove the rear seat cover cap.

    HINT:
    Tape the screwdriver tip before use.


16. REMOVE REAR CENTER BACK LOCK CONTROL LEVER

B237965
  1. Remove the 2 screws.

  1. Move the rear center back lock control lever in the direction of the arrow to detach the guide and remove the rear center back lock control lever.

  1. Detach the cable clamp and disconnect the cable from the rear center back lock control lever.


17. REMOVE REAR SEATBACK COVER

B237641
  1. Using a screwdriver, detach the 4 claws and remove the rear seatback cover.

    HINT:
    Tape the screwdriver tip before use.


18. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH

B237915
  1. Using a clip remover, detach the 7 clips and remove the rear seatback board carpet assembly RH.


19. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

B237672
  1. Detach the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.


20. REMOVE SEATBACK COVER WITH PAD

  1. B237916E01
    Remove the 14 hog rings and detach the hooks, and then remove the seatback cover with pad.
    Text in Illustration 
    *1
    Hook
    *2
    Hog Ring

  1. w/ Seat Heater System:

    1. B360128
      Remove the wire harness.


21. REMOVE SEPARATE TYPE REAR SEATBACK COVER

  1. B248337
    w/ Seat Heater System:

    1. Disconnect the rear seatback heater assembly wire harness from the separate type rear seatback pad.

  1. B241213
    Remove the 8 hog rings and separate type rear seatback cover from the separate type rear seatback pad.


22. REMOVE REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

B248650E01
  1. Cut off the 11 tack pins which fasten the rear seatback heater assembly to the separate type rear seatback cover, and then remove the rear seatback heater assembly from the separate type rear seatback cover.

    Text in Illustration 
    *1
    Tack Pin


23. REMOVE REAR SEATBACK EDGE PROTECTOR
  1. Remove the rear seatback edge protector from the rear seatback frame sub-assembly RH.


24. REMOVE REAR SEAT INNER RECLINING COVER RH

B237920
  1. Remove the 2 screws.

  1. Detach the guide and remove the rear seat inner reclining cover RH.


25. REMOVE RECLINING ADJUSTER INSIDE COVER RH

B237770
  1. Remove the 2 screws.

  1. Detach the 2 claws and remove the reclining adjuster inside cover RH.


26. REMOVE RECLINING ADJUSTER INSIDE COVER RH

B237918
  1. Using a clip remover, detach the clip.

  1. Move the reclining adjuster inside cover RH in the direction of the arrow to detach the 2 claws and remove the reclining adjuster inside cover RH.


27. REMOVE RECLINING ADJUSTER INSIDE COVER RH

B237919
  1. Detach the claw and guide, and remove the reclining adjuster inside cover RH.


28. REMOVE REAR SEAT CUSHION SPRING DAMPER

B237967
  1. Remove the 2 nuts and rear seat cushion spring damper.


29. REMOVE REAR SEATBACK SPRING DAMPER (w/ Dynamic Damper)

  1. B295840
    Remove the 2 nuts and rear seatback spring damper.


30. REMOVE REAR SEAT RECLINING CONTROL CABLE

  1. Cut off the 3 cable ties.

    B237921

  1. Detach the 2 cable clamps and disconnect the rear seat reclining control cable, and then remove the rear seat reclining control cable.

    B237922


31. REMOVE REAR NO. 2 SEAT RECLINING CONTROL CABLE

  1. Detach the cable clamp and disconnect the rear No. 2 seat reclining control cable, and then remove the rear No. 2 seat reclining control cable.

    B237923


32. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

B248345
  1. Disconnect the connector.

  1. Detach the 2 clamps and remove the seat heater control sub-assembly.


33. REMOVE REAR SEAT WIRE RH (w/ Seat Heater System)

  1. B249861
    Detach the claw and disconnect the rear seat wire connector.

  1. Detach the clamp and remove the rear seat wire RH.


34. REMOVE REAR SEAT CUSHION SET PLATE

B237924
  1. Remove the 2 nuts and rear seat cushion set plate.


35. REMOVE REAR SEATBACK LOCK PLATE LH
  1. Detach the 2 cable clamps and disconnect the cable.

  1. Remove the nut and rear seatback lock plate LH.

    B237925


36. REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY RH

B237926
  1. Using a T45 "TORX" socket wrench, remove the 4 "TORX" bolts and rear seatback frame sub-assembly RH.


37. REMOVE REAR SEAT COVER

B237927
  1. Remove the screw and rear seat cover.


38. REMOVE REAR SEAT CUSHION SPRING

B237928
  1. Detach the 2 hooks and remove the rear seat cushion spring.


39. REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH

B237932E01
  1. Remove the 6 nuts and rear seat cushion frame sub-assembly RH together with the No. 1 seat leg plate.

    Text in Illustration 
    *1
    No. 1 Seat Leg Plate


40. REMOVE REAR SEAT TRACK ADJUSTING HANDLE RH

  1. B237929
    Remove the seat cushion side frame sub-assembly RH.

  1. B237930
    Slide the slide rail to the rearmost position.

  1. Using a small screwdriver, push down the handle stopper to detach the claw and remove the rear seat track adjusting handle RH.

    HINT:
    Insert the screwdriver in the hole shown into the illustration while looking into the hole.

← REMOVAL (from Aug 2013)REASSEMBLY (from Aug 2013) →