2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.


1. REMOVE REAR SEAT CUSHION

B238042
  1. Remove the 2 screws and 2 cushions.


2. REMOVE REAR SEATBACK PROTECTOR

B238024
  1. Remove the 2 screws.

  1. Detach the 2 hooks and remove the protector.


3. REMOVE REAR SEAT CUSHION UNDER COVER RH

B238043
  1. Using a moulding remover, detach the hooks and remove the cover.


4. REMOVE SEAT CUSHION COVER WITH PAD

B238045
  1. Disconnect the seat cushion band from the seat cushion cover.

  1. Detach the hooks and remove the seat cushion cover with pad.


5. REMOVE NO. 1 SEAT CUSHION COVER RH

B238049E01
  1. Cut off the tack pins and remove the cover from the cushion pad.

    Text in Illustration 
    *1
    Tack Pin


6. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER RH

B238050
  1. Remove the hog rings and seat cushion cover from the seat cushion pad.


7. REMOVE REAR SEAT CUSHION BAND

B238047
  1. Remove the band as shown in the illustration.


8. REMOVE REAR SEAT LEG BRACKET COVER

B237994
  1. Using a moulding remover, detach the 4 claws and remove the cover.

    HINT:
    Use the same procedure for both covers.


9. REMOVE REAR SEAT LEG COVER

B237996
  1. Detach the claw and guide, and then remove the cover.

    HINT:
    Use the same procedure for both covers.


10. REMOVE NO. 1 SEATBACK BOARD SUB-ASSEMBLY

B238055
  1. Using a clip remover, detach the 3 clips.

  1. Detach the guide and remove the board.


11. REMOVE REAR SEAT INNER RECLINING COVER RH

B238056
  1. Remove the screw.

  1. Detach the 2 guides and remove the cover.


12. REMOVE REAR SEAT CENTER INNER BELT ASSEMBLY

B241736E02
  1. Detach the fastening tape and remove the band.

  1. Remove the bolt and inner belt.

    Text in Illustration 
    *1
    Band


13. REMOVE CENTER SEATBACK COVER SUB-ASSEMBLY

B238058
  1. Remove the screw.

  1. Detach the 2 guides and remove the cover.


14. REMOVE CENTER SEATBACK ASSEMBLY

B238059
  1. Using a T45 "TORX" socket wrench, remove the "TORX" bolt and bush.

  1. Remove the 2 bolts and center seatback.


15. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY
  1. Remove the headrest.


16. REMOVE CENTER SEAT HINGE COVER

B238060
  1. Detach the claw and remove the cover.


17. REMOVE REAR SEATBACK STAY COVER LH

B238062
  1. Detach the 3 claws and remove the cover.


18. REMOVE REAR SEATBACK STAY COVER RH

  1. B238061
    Using a T45 "TORX" socket wrench, remove the "TORX" bolt, bush and hinge.

  1. B238063
    Detach the 3 claws and remove the cover.


19. REMOVE REAR CENTER SEAT ARMREST ASSEMBLY

B238064
  1. Using a T45 "TORX" socket wrench, remove the 2 "TORX" bolts, 2 bushes and armrest.

  1. B238065
    Remove the bush.


20. REMOVE NO. 2 CUP HOLDER ASSEMBLY RH

B238066
  1. Remove the 2 cup holders.


21. REMOVE REAR SEATBACK COVER

  1. B237641
    Using a screwdriver, detach the 4 claws and remove the cover.

    HINT:
    Tape the screwdriver tip before use.


22. REMOVE REAR SEATBACK LOCK COVER

B237735
  1. Using a moulding remover, detach the claw.

  1. Move the cover in the direction of the arrow to detach the clip and 2 guides and remove the cover.


23. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY

B238067
  1. Detach the 4 claws and 3 clips, and then remove the board.


24. REMOVE REAR SEAT HEADREST SUPPORT

B238068
  1. Detach the 4 claws and remove the 2 supports.


25. REMOVE REAR NO. 1 SEAT NO. 2 SIDE PLATE

  1. B238069
    Remove the 2 screws.

  1. B238070
    Using a moulding remover, detach the 3 claws and remove the plate.


26. REMOVE REAR SEAT LOCK ASSEMBLY RH

B238072
  1. Detach the clamp and disconnect the wire.

  1. Remove the 2 bolts and lock.


27. REMOVE REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH

B238073
  1. Remove the 2 screws and control lever.


28. REMOVE CENTER NO. 2 SEATBACK COVER

B238074
  1. Remove the screw.

  1. Detach the 2 claws and remove the cover.


29. REMOVE REAR SEATBACK LOCK COVER RH

B238025
  1. Remove the 2 screws.

  1. Detach the 2 guides and remove the cover.


30. REMOVE REAR SEATBACK LOCK ASSEMBLY RH

  1. B238080
    Remove the 2 hog rings.

  1. B238081
    Remove the 2 bolts.

  1. While moving the release button in the direction of the arrow in the illustration, detach it from the grommet and remove the seatback lock.


31. REMOVE REAR SEATBACK LOCK RELEASE BUTTON

B238009
  1. Remove the release button as shown in the illustration.

    Text in Illustration 
    V100135
    Counterclockwise


32. REMOVE REAR SEATBACK STOP BUTTON GROMMET

B238027
  1. Detach the 3 claws and remove the grommet.


33. REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

B238003
  1. Detach the 4 claws and remove the 2 supports.


34. REMOVE SEAT BELT ANCHOR COVER CAP

B238075E01
  1. Using a screwdriver, detach the 2 claws and 2 guides, and then remove the cap.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


35. REMOVE REAR SEAT SHOULDER BELT COVER

B238077
  1. Remove the screw.

  1. Detach the 3 claws and remove the cover.

  1. Disconnect the outer belt from the cover.


36. REMOVE REAR SEATBACK LOCK STRIKER PROTECTOR

B238078
  1. Remove the protector from the striker.


37. REMOVE REAR SEAT LOCK STRIKER

B238079
  1. Using a T45 "TORX" socket wrench, remove the striker.


38. REMOVE SEATBACK COVER WITH PAD

B238083E01
  1. Remove the hog rings, detach the hook, and then remove the seatback cover with pad.

    Text in Illustration 
    *1
    Hook
    *2
    Hog Ring

  1. Disconnect the outer belt from the seatback cover with pad.


39. REMOVE SEPARATE TYPE REAR SEATBACK COVER RH

B238028
  1. Remove the hog rings and cover from the seatback pad.


40. REMOVE REAR SEATBACK EDGE PROTECTOR
  1. Remove the protector from the seatback frame.


41. REMOVE REAR SEAT SHOULDER BELT GUIDE

B238085
  1. Detach the claw and guide, and then remove the belt guide.


42. REMOVE NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY RH

B241741
  1. Remove the nut and bolt, and then detach the 2 claws and remove the seat belt.


43. REMOVE REAR NO. 1 SEAT PROTECTOR LH

B238087
  1. Detach the 2 claws and remove the protector.


44. REMOVE REAR NO. 1 SEAT PROTECTOR RH

B238086
  1. Detach the claw and remove the protector.

← REMOVAL (from Aug 2014)REASSEMBLY (from Aug 2013) →