REMOVAL
Removal / installation · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
| 1.
REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)
|
 |
- HINT:
- Use the same procedure for all rear No. 1 floor step covers.
Using a screwdriver, detach the 2 claws and remove the rear No. 1 floor step cover.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration
*1
|
Protective Tape
|
| 2.
REMOVE QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)
|
 |
- HINT:
- Use the same procedure described for the LH side.
| 3.
REMOVE REAR DOOR SCUFF PLATE RH
|
 |
- HINT:
- Use the same procedure described for the LH side.
| 4.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
|
 |
- HINT:
- Use the same procedure described for the LH side.
| 5.
REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
|
 |
Remove the tonneau cover.
| 6.
REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)
|
 |
- HINT:
- Use the same procedure for the other front luggage compartment trim cover.
Detach the 4 claws and remove the cap.
- Remove the bolt, luggage hold belt striker and front luggage compartment trim cover.
Text in Illustration
*1
|
Luggage Hold Belt Striker
|
| 7.
REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)
|
 |
Detach the clip and remove the No. 1 deck board.
| 8.
REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
|
 |
Detach the 5 clips and 4 claws and remove the rear floor mat rear support plate.
| 9.
REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)
|
 |
Remove the 3 bolts and floor side rail.
| 10.
REMOVE FLOOR SIDE RAIL RH (w/ Deck Rail)
|
 |
- HINT:
- Use the same procedure described for the LH side.
| 11.
REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)
|
 |
Detach the 4 claws and remove the rear floor carpet.


Text in Illustration
*A
|
w/o Deck Rail
|
*B
|
w/ Deck Rail
|
*C
|
for Face to Face Seat Type
|
-
|
-
|
| 12.
REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
|
 |
- HINT:
- Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.
Detach the 3 claws and remove the rear No. 1 seat outer lap belt anchor cover.
| 13.
REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
|
 |
- HINT:
- Use the same procedure for the other No. 1 luggage compartment trim hook.
Remove the luggage compartment trim hook by turning it clockwise.
| 14.
REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)
|
 |
- HINT:
- Use the same procedure for the other No. 1 tonneau cover holder cap.
Using a screwdriver, detach the 2 claws and remove the No. 1 tonneau cover holder cap.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration
*1
|
Protective Tape
|
| 15.
REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)
|
 |
- HINT:
- Use the same procedure for the other front deck side trim cover.
Using a screwdriver, detach the 2 claws and remove the front deck side trim cover.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration
*1
|
Protective Tape
|
| 16.
REMOVE ASSIST GRIP PLUG (w/ Rear No. 2 Seat)
|
 |
- HINT:
- Use the same procedure for all assist grip plugs.
Using a screwdriver, detach the 2 claws and remove the assist grip plug.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration
*1
|
Protective Tape
|
| 17.
REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)
|
 |
- HINT:
- Use the same procedure for the other assist grip.
Remove the 2 bolts and assist grip.
| 18.
REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
|
 |
w/o Rear No. 2 Seat:
- Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
- Detach the 6 claws and 2 guides and disconnect the rear seatback lock control lever base.
Remove the 4 bolts and screws.
Detach the 5 clips and 8 claws.
Disconnect each connector.
Pass the rear seatback lock control lever base through the deck trim side panel and remove the deck trim side panel.


w/ Rear No. 2 Seat:
- Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
- Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.
Remove the 2 bolts and screw.
Detach the 4 clips and 8 claws.
Disconnect each connector and remove the deck trim side panel.


| 19.
REMOVE VOLTAGE INVERTER ASSEMBLY |
 |
- Disconnect the connector.
Remove the 2 bolts and voltage inverter.