2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Aug 2013

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY

  1. E283079
    Detach the 4 clips.

  1. Disconnect the connector and remove the integration control and panel assembly.


2. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

B356216
  1. Detach the 4 clips and remove the instrument panel finish panel end LH.


3. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

B356215
  1. Detach the 5 clips and remove the No. 2 instrument panel finish panel cushion.


4. REMOVE INSTRUMENT PANEL FINISH PANEL END RH

B356217
  1. Detach the 4 clips and remove the instrument panel finish panel end RH.


5. REMOVE NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION

HINT:
Use the same procedure described for the No. 2 instrument panel finish panel cushion.


6. REMOVE FRONT CONSOLE UPPER PANEL GARNISH

  1. w/o Seat Heater System:

    1. B357641E01
      Put protective tape around the front console upper panel garnish.
      Text in Illustration 
      *1
      Protective Tape

    2. Detach the 5 clips and remove the front console upper panel garnish.

    3. Disconnect the connector.

  1. w/o CRAWL:

    1. B357639E01
      Put protective tape around the front console upper panel garnish.
      Text in Illustration 
      *1
      Protective Tape

    2. Detach the 5 clips and remove the front console upper panel garnish.

    3. Disconnect each connector.

  1. w/ CRAWL:

    1. B357640E01
      Put protective tape around the front console upper panel garnish.
      Text in Illustration 
      *1
      Protective Tape

    2. Detach the 5 clips and remove the front console upper panel garnish.


7. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

B356218
  1. for LHD:

    1. Remove the screw.

    2. Detach the 2 clips and 2 guides and remove the No. 1 instrument panel under cover.

    3. Disconnect each connector.

  1. B298554
    for RHD:

    1. Remove the screw.

    2. Detach the 3 clips and 2 guides and remove the No. 1 instrument panel under cover.

    3. Disconnect each connector.


8. REMOVE FRONT NO. 1 CONSOLE BOX INSERT

B238139
  1. Detach the 2 clips and guide and remove the front No. 1 console box insert.


9. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
  1. Remove the screw.

  1. Detach the 3 clips and 2 guides and remove the No. 2 instrument panel under cover.

    B298555E01

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD


10. REMOVE FRONT NO. 2 CONSOLE BOX INSERT

B238145
  1. Detach the 2 clips and guide and remove the front No. 2 console box insert.


11. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

B363298E01
  1. Move the shifting hole cover downward.

    Text in Illustration 
    *1
    Shifting Hole Cover

  1. Twist the shift lever knob in the direction indicated by the arrow and remove it.


12. REMOVE CONSOLE PANEL SUB-ASSEMBLY

B238141E01
  1. Put protective tape around the console panel.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 8 clips and 2 claws.

  1. Disconnect each connector and remove the console panel.


13. REMOVE NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY (w/ Cool Box)

B238153
  1. Detach the 4 claws.

  1. Disconnect the 2 clamps and remove the No. 1 heater to register duct.


14. REMOVE NO. 1 CONSOLE BOX DUCT (for Single Air Conditioning System)

B363311
  1. Remove the clip and No. 1 console box duct.


15. REMOVE REAR CONSOLE END PANEL SUB-ASSEMBLY

B238142
  1. Detach the 4 clips and 4 claws.

  1. Disconnect each connector and remove the rear console end panel.


16. REMOVE REAR CONSOLE BOX ASSEMBLY

B363312
  1. Remove the 2 screws, clip and 5 bolts.

  1. Disconnect each connector and remove the rear console box.

← COMPONENTS (from Aug 2013)DISASSEMBLY (from Aug 2013) →