2013-2015 Land Cruiser Prado · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. REMOVE MANUAL TRANSMISSION FILLER PLUG

  1. D029023E01
    Remove the manual transmission filler plug and gasket from the manual transmission case.


2. REMOVE DRAIN PLUG

  1. D029024E01
    Remove the drain plug and gasket from the manual transmission case.


3. REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

C215530
  1. Remove the release fork and release bearing from the clutch housing.


4. REMOVE CLUTCH RELEASE BEARING ASSEMBLY

C067602E01
  1. Remove the clip and release bearing from the release fork.


5. REMOVE RELEASE FORK SUPPORT

  1. D025933E01
    Remove the release fork support from the clutch housing.


6. REMOVE CLUTCH RELEASE FORK BOOT

  1. C216207
    Remove the clutch release fork boot from the clutch housing.


7. REMOVE CLUTCH HOUSING

  1. C216208
    Remove the 9 bolts.

  1. D029029E01
    Using a plastic-faced hammer, tap off the clutch housing from the manual transmission case.


8. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

  1. D029030E09
    Using SST, remove the back-up light switch assembly and gasket from the manual transmission case.
    SST
    09817-16011  


9. REMOVE RESTRICT PIN

  1. C216210
    Remove the 2 restrict pins from the transfer adapter.


10. REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

  1. C216211
    Remove the 4 bolts and floor shift control shift lever retainer sub-assembly.

  1. Remove the gasket.


11. REMOVE TRANSFER ADAPTER

  1. C216214
    Remove the 10 bolts.

  1. C216215
    Using a brass bar and hammer, tap off the transfer adapter from the manual transmission case.


12. REMOVE TRANSFER OIL RECEIVER PIPE

  1. D029037E01
    Remove the transfer oil receiver pipe from the transfer adapter.


13. REMOVE SHIFT AND SELECT LEVER

  1. C216209
    Remove the bolt from the shift lever housing.

  1. C216212E01
    Remove the shift and select lever and shift lever housing from the transfer adapter.
    Text in Illustration 
    *1
    Shift Lever Housing
    *2
    Shift and Select Lever


14. REMOVE REVERSE RESTRICT PIN ASSEMBLY

  1. D029040E01
    Using a T40 "TORX" socket wrench, remove the reverse restrict pin plug.

  1. D033421E01
    Using a 5 mm pin punch and hammer, tap out the reverse restrict pin slotted spring pin.

  1. D029042E01
    Remove the reverse restrict pin assembly.


15. REMOVE TRANSFER ADAPTER OIL SEAL

  1. D029043E01
    Using a screwdriver and hammer, tap out the transfer adapter oil seal from the transfer adapter.


16. REMOVE FRONT BEARING RETAINER

  1. D025950E01
    Remove the 8 bolts.

  1. D025951E01
    Using a brass bar and hammer, tap off the front bearing retainer from the manual transmission case.


17. REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL

  1. C215999E01
    Secure the front bearing retainer in a vise between aluminum plates.

  1. Using SST, tap out the transmission front bearing retainer oil seal.

    SST
    09308-00010  


18. REMOVE FRONT BEARING SHAFT SNAP RING

  1. D025953E01
    Using a snap ring expander, remove the front bearing shaft snap ring from the input shaft front bearing.


19. REMOVE FRONT NO. 1 COUNTER GEAR BEARING SNAP RING

  1. D025954E01
    Using a snap ring expander, remove the front No. 1 counter bearing snap ring from the front counter gear bearing.


20. REMOVE MANUAL TRANSMISSION CASE

  1. D029044E01
    Using a brass bar and hammer, tap off the manual transmission case from the intermediate plate.


21. REMOVE TRANSMISSION MAGNET

  1. D025957E01
    Remove the transmission magnet from the intermediate plate.


22. FIX INTERMEDIATE PLATE

  1. C288239
    Secure the intermediate plate in a vise between aluminum plates.


23. REMOVE NO. 1 SHIFT DETENT BALL SPRING SEAT

  1. C295052
    for Type A:
    Using a 6 mm hexagon socket wrench, remove the No. 1 shift detent ball spring seat from the intermediate plate.

  1. D029046E01
    for Type B:
    Using a T40 "TORX" socket wrench, remove the No. 1 shift detent ball spring seat from the intermediate plate.

  1. D025960E01
    Using a magnet hand, remove the compression spring and detent ball from the intermediate plate.

  1. C295053
    for Type A:
    Using a 6 mm hexagon socket wrench, remove the 2 No. 1 shift detent ball spring seats from the intermediate plate.

  1. C288240
    for Type B:
    Using a T40 "TORX" socket wrench, remove the 2 No. 1 shift detent ball spring seats from the intermediate plate.

  1. C288241
    Using a magnet hand, remove the 2 compression springs and 2 detent balls from the intermediate plate.


24. REMOVE NO. 2 GEAR SHIFT FORK SHAFT

  1. C288242
    Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 2 gear shift fork shaft.

    NOTICE:
    Use a piece of cloth to prevent the snap ring from flying off.

  1. C288243
    Remove the bolt from the No. 2 shift fork.

  1. C288244
    Remove the No. 2 gear shift fork shaft from the intermediate plate.

  1. C288245
    Remove the No. 2 shift fork from the No. 2 transmission hub sleeve.

  1. D025967E01
    Using a magnet hand, remove the No. 1 shift interlock roller and shift interlock pin from the intermediate plate.


25. REMOVE NO. 1 GEAR SHIFT FORK SHAFT

  1. C288246
    Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 1 gear shift fork shaft.

    NOTICE:
    Use a piece of cloth to prevent the snap ring from flying off.

  1. C288247
    Remove the bolt from the No. 1 shift fork.

  1. C288248
    Remove the No. 1 gear shift fork shaft from the intermediate plate.

  1. C288249
    Remove the No. 1 shift fork from the reverse gear.


26. REMOVE NO. 3 GEAR SHIFT FORK SHAFT

  1. C272919
    Using a 5 mm pin punch and hammer, tap out the shift fork set slotted spring pin from the No. 3 shift fork.

  1. C288250
    Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 3 gear shift fork shaft.

    NOTICE:
    Use a piece of cloth to prevent the snap ring from flying off.

  1. C289009
    Using a magnet hand, remove the straight pin from the reverse shift fork.

  1. D029058E01
    Remove the No. 3 shift fork and No. 3 gear shift fork shaft from the intermediate plate.

  1. D025975E02
    Using a magnet hand, remove the No. 1 shift interlock roller from the intermediate plate.


27. REMOVE REVERSE SHIFT FORK

  1. C290803
    Remove the reverse shift fork from the reverse shift arm.


28. REMOVE REVERSE SHIFT ARM BRACKET

  1. C291033
    Remove the torsion spring from the reverse shift arm bracket.

  1. C291034
    Remove the 2 bolts and reverse shift arm bracket from the intermediate plate.

  1. C291035
    Using a screwdriver, pry out the snap ring from the reverse shift arm bracket.

  1. C291036
    Remove the reverse shift arm from the reverse shift arm bracket.


29. REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING (for Rear Bearing Side)

  1. D029059E01
    Using 2 screwdrivers and a hammer, tap off the output shaft bearing shaft snap ring from the output shaft rear bearing.

    NOTICE:
    Use a piece of cloth to prevent the snap ring from flying off.


30. REMOVE OUTPUT SHAFT REAR BEARING

  1. C295486E01
    Using SST, remove the output shaft rear bearing and output shaft spacer from the output shaft.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04051, 09957-04010, 09958-04011)
    09950-60010   (09951-00300)
    Text in Illustration 
    *a
    Hold
    *b
    Turn


31. INSPECT COUNTER 5TH GEAR THRUST CLEARANCE

  1. D025991E01
    Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.00394 to 0.0137 in.)

    1. If the clearance is not as specified, replace the counter 5th gear.


32. INSPECT COUNTER 5TH GEAR RADIAL CLEARANCE

  1. D025992E01
    Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.015 to 0.068 mm (0.000591 to 0.00267 in.)

    1. If the clearance is not as specified, replace the counter 5th gear bearing with a new one.


33. REMOVE COUNTER GEAR REAR SHAFT SNAP RING

  1. C272923
    Using 2 screwdrivers and a hammer, tap off the counter gear rear shaft snap ring from the counter gear.

    NOTICE:
    Use a piece of cloth to prevent the counter gear rear shaft snap ring from flying off.


34. REMOVE NO. 3 TRANSMISSION HUB SLEEVE

  1. C282116
    Remove the No. 3 transmission hub sleeve from the counter 5th gear.


35. REMOVE NO. 5 GEAR SPLINE PIECE

  1. C295487E01
    Using SST, remove the counter 5th gear together with the counter 5th gear bearing, 2 No. 3 synchromesh shifting keys, No. 3 synchromesh shifting key spring, No. 3 synchronizer ring and No. 5 gear spline piece from the counter 5th gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021, 09957-04010)
    Text in Illustration 
    *a
    Hold
    *b
    Turn


36. REMOVE NO. 5 GEAR SPLINE PIECE

  1. C250776
    Remove the No. 5 gear spline piece from the counter 5th gear.


37. REMOVE OUTER NO. 3 SYNCHRONIZER RING
  1. Remove the outer No. 3 synchronizer ring from the counter 5th gear.


38. REMOVE COUNTER 5TH GEAR BEARING

  1. C089839E01
    Remove the counter 5th gear bearing from the counter 5th gear.


39. REMOVE NO. 3 SYNCHROMESH SHIFTING KEY

  1. C247403
    Using a snap ring expander, remove the shaft snap ring.

  1. C250077E01
    Remove the No. 3 synchromesh shifting keys and No. 3 synchromesh shifting key spring from the counter 5th gear.
    Text in Illustration 
    *1
    No. 3 Synchromesh Shifting Key Spring
    *2
    No. 3 Synchromesh Shifting Key
    *3
    Counter 5th Gear


40. REMOVE 5TH GEAR THRUST WASHER

  1. C272927
    Remove the 5th gear thrust washer from the counter gear.


41. REMOVE 5TH GEAR THRUST WASHER PIN

  1. C272929
    Remove the 5th gear thrust washer pin from the counter gear.


42. REMOVE OUTPUT SHAFT REAR BEARING RETAINER

  1. D026001E01
    Remove the 4 bolts and output shaft rear bearing retainer from the intermediate plate.


43. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

  1. D026002E01
    Pull out the reverse idler gear shaft from the rear side and remove the reverse idler gear sub-assembly from the intermediate plate.


44. REMOVE COUNTER SHAFT CENTER BEARING

  1. C272931
    Using a snap ring expander, remove the snap ring from the counter shaft center bearing.

  1. C295488E01
    Using SST, remove the counter shaft center bearing from the intermediate plate.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)
    09950-60010   (09951-00260)

    NOTICE:
    Do not drop the counter gear. Hold the front side of the counter gear when removing the bearing outer race.


45. REMOVE COUNTER GEAR

  1. D026005E01
    Remove the counter gear from the intermediate plate.


46. REMOVE INPUT SHAFT

  1. D026006E01
    Remove the input shaft and No. 2 synchronizer ring from the output shaft.

    NOTICE:
    Do not drop the input shaft bearing or No. 2 synchronizer ring.


47. REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING (for Center Bearing Side)

  1. C272935
    Using a snap ring expander, remove the output shaft bearing shaft snap ring from the output shaft center bearing.


48. REMOVE OUTPUT SHAFT

  1. C272539
    Using a plastic-faced hammer, remove the output shaft by tapping the intermediate plate.

← COMPONENTS (from Aug 2013)INSPECTION (from Aug 2013) →