2013-2015 Land Cruiser Prado · Service Manual Drivetrain

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. INSTALL OUTPUT SHAFT

  1. C272540
    Apply gear oil to the sliding part of the output shaft.

  1. Using a plastic-faced hammer, install the output shaft by tapping the intermediate plate.


2. INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING (for Center Bearing Side)

  1. C272935
    Using a snap ring expander, install the output shaft bearing shaft snap ring to the output shaft center bearing.


3. INSTALL INPUT SHAFT

  1. C291275
    Apply gear oil to the input shaft and No. 2 synchronizer ring, and install them to the output shaft.

    NOTICE:
    1. Install the No. 2 synchronizer ring so that its groove fits onto the No. 2 synchromesh shifting key.
    2. Check that the input shaft rotates smoothly.


4. INSTALL COUNTER GEAR

  1. C291291
    Install the counter gear to the intermediate plate.


5. INSTALL COUNTER SHAFT CENTER BEARING

  1. C216003E01
    Using SST and a hammer, tap in a new counter shaft center bearing to the intermediate plate.
    SST
    09316-60011  

    HINT:
    Install the counter shaft center bearing while tapping the tip of the counter gear with a plastic-faced hammer so that the counter gear does not hit the side wall of the output shaft gear by being pushed forward.

  1. Using a snap ring expander, install the snap ring to the counter shaft center bearing.


6. INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY

  1. D026002E02
    Apply gear oil to the sliding parts of the reverse idler gear sub-assembly and reverse idler gear shaft, and install the reverse idler gear sub-assembly and reverse idler shaft to the intermediate plate.

    NOTICE:
    Be sure to install the reverse idler gear shaft from the rear with the groove facing the rear side.


7. INSTALL OUTPUT SHAFT REAR BEARING RETAINER

  1. D026001E02
    Insert the protrusion of the output shaft rear bearing retainer into the groove of the reverse idler gear shaft. Then install the output shaft rear bearing retainer with the 4 bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


8. INSTALL 5TH GEAR THRUST WASHER PIN

  1. C272929
    Apply MP grease to the 5th gear thrust washer pin and install it to the counter gear.


9. INSTALL 5TH GEAR THRUST WASHER

  1. C272927
    Apply gear oil to the 5th gear thrust washer and install it to the counter gear.

    NOTICE:
    Install the 5th gear thrust washer so that its chamfered side faces the front side.


10. INSTALL NO. 3 SYNCHROMESH SHIFTING KEY
  1. Apply gear oil to the sliding part of No. 3 transmission hub sleeve and install it to the counter 5th gear.

    NOTICE:
    Make sure that the No. 3 transmission hub sleeve and counter 5th gear are facing the proper direction.

  1. C248514E01
    Install the 2 No. 3 synchromesh shifting keys and No. 3 synchromesh shifting key spring to the counter 5th gear as shown in the illustration.
    Text in Illustration 
    *a
    Cutout
    *b
    Protrusion

    HINT:
    When installing the No. 3 synchromesh shifting key spring, make sure the protrusion fits into the cutout.

  1. C247403
    Using a snap ring expander, install the snap ring to the counter 5th gear.


11. INSTALL COUNTER 5TH GEAR BEARING

  1. D026020E01
    Apply gear oil to the counter 5th gear bearing and install it to the counter 5th gear.


12. INSTALL COUNTER 5TH GEAR

  1. C272976
    Apply gear oil to the counter 5th gear and No. 3 transmission hub sleeve, and install the counter 5th gear to the counter gear.


13. INSTALL OUTER NO. 3 SYNCHRONIZER RING

  1. C272978
    Apply gear oil to the outer No. 3 synchronizer ring and install it to the counter gear.

    NOTICE:
    Install the outer No. 3 synchronizer ring so that its groove fits onto the No. 3 synchromesh shifting key.


14. INSTALL NO. 5 GEAR SPLINE PIECE

  1. C216004E01
    Using SST and a press, press in the No. 5 gear spline piece to the counter gear.
    SST
    09316-60011   (09316-00011)

    NOTICE:
    Check that the counter 5th gear rotates freely.


15. INSTALL COUNTER GEAR REAR SHAFT SNAP RING
  1. Select a counter gear rear shaft snap ring so that the thrust clearance between the No. 5 gear spline piece and counter gear rear shaft snap ring to be within the specification.

    Standard clearance:
    0.10 mm (0.00394 in.) or less

    Snap Ring Thickness:
    Thickness
    2.85 mm (0.1122 in.)
    2.90 mm (0.1141 in.)
    2.95 mm (0.1161 in.)
    3.00 mm (0.1181 in.)
    3.05 mm (0.1200 in.)
    3.10 mm (0.1220 in.)
    3.15 mm (0.1240 in.)

  1. Secure the intermediate plate in a vise between aluminum plates.

  1. D026023E01
    Using a brass bar and hammer, tap on the counter gear rear shaft snap ring.


16. INSPECT COUNTER 5TH GEAR THRUST CLEARANCE

  1. D025991E01
    Using a feeler gauge, measure the thrust clearance.

    Standard clearance:
    0.10 to 0.35 mm (0.00394 to 0.0137 in.)

    1. If the clearance is not as specified, replace the counter 5th gear.


17. INSPECT COUNTER 5TH GEAR RADIAL CLEARANCE

  1. D025992E01
    Using a dial indicator, measure the radial clearance.

    Standard clearance:
    0.015 to 0.068 mm (0.000591 to 0.00267 in.)

    1. If the clearance is not as specified, replace the counter 5th gear bearing with a new one.


18. INSTALL OUTPUT SHAFT REAR BEARING

  1. C216005E01
    Using SST and a hammer, press in the output shaft spacer and a new output shaft rear bearing to the output shaft.
    SST
    09309-35010  


19. INSTALL OUTPUT SHAFT BEARING SHAFT SNAP RING (for Rear Bearing Side)
  1. Select a output shaft bearing shaft snap ring so that the thrust clearance between the output shaft bearing shaft and output shaft bearing shaft snap ring to be within the specification.

    Standard clearance:
    0.10 mm (0.00394 in.) or less


    Snap Ring Thickness:
    Thickness
    Thickness
    2.65 mm (0.1043 in.)
    3.10 mm (0.1220 in.)
    2.70 mm (0.1063 in.)
    3.15 mm (0.1240 in.)
    2.75 mm (0.1083 in.)
    3.20 mm (0.1260 in.)
    2.80 mm (0.1102 in.)
    3.25 mm (0.1280 in.)
    2.85 mm (0.1122 in.)
    3.30 mm (0.1299 in.)
    2.90 mm (0.1142 in.)
    3.35 mm (0.1319 in.)
    2.95 mm (0.1161 in.)
    3.40 mm (0.1339 in.)
    3.00 mm (0.1181 in.)
    3.45 mm (0.1358 in.)
    3.05 mm (0.1200 in.)
    -

  1. D025988E01
    Using a brass bar and hammer, tap on the output shaft bearing shaft snap ring.


20. INSTALL REVERSE SHIFT ARM BRACKET

  1. C291035
    Install the reverse shift arm to the reverse shift arm bracket with a new snap ring.

  1. C291038E02
    Insert the tip of the reverse shift arm into the reverse idler gear sub-assembly.
    Text in Illustration 
    *1
    Reverse Idler Gear Sub-assembly
    *2
    Reverse Shift Arm

  1. C291034
    Install the reverse shift arm bracket with the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Install the torsion spring to the reverse shift arm bracket.

    NOTICE:
    Make sure that the torsion spring is securely installed to the reverse shift arm.


21. INSTALL REVERSE SHIFT FORK

  1. C290803
    Install the reverse shift fork to the reverse shift arm.


22. INSTALL NO. 3 GEAR SHIFT FORK SHAFT

  1. C272921
    Install the No. 3 shift fork to the No. 3 transmission hub sleeve and the No. 3 gear shift fork shaft to the intermediate plate from the front side.

  1. C289009
    Install the straight pin to the reverse shift fork.

  1. C288251
    Using a brass bar and hammer, tap on the snap ring to the No. 3 gear shift fork shaft.

  1. C272919
    Using a 5 mm pin punch and hammer, tap on the shift fork set slotted spring pin to the No. 3 shift fork.


23. INSTALL NO. 1 GEAR SHIFT FORK SHAFT

  1. D025975E04
    Install the No. 1 shift interlock roller to the intermediate plate.

  1. C288249
    Install the No. 1 shift fork to the reverse gear.

  1. C288248
    Install the No. 1 gear shift fork shaft to the intermediate plate from the rear side.

  1. C288247
    Install a new bolt to the No. 1 shift fork.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

  1. C288252
    Using a brass bar and hammer, tap in the snap ring to the No. 1 gear shift fork shaft.


24. INSTALL NO. 2 GEAR SHIFT FORK SHAFT

  1. D025967E02
    Install the shift interlock pin and No. 1 shift interlock roller to the intermediate plate.

  1. C288245
    Install the No. 2 shift fork to the No. 2 transmission hub sleeve.

  1. D029050E02
    Apply gear oil to the No. 2 gear shift fork shaft and install it to the intermediate plate from the rear side.

  1. C288243
    Install a new bolt to the No. 2 shift fork.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

  1. C288253
    Using a brass bar and hammer, tap on the snap ring to the No. 2 gear shift fork shaft.


25. INSTALL NO. 1 SHIFT DETENT BALL SPRING SEAT

  1. C288241
    Install the 2 detent balls and 2 compression springs to the intermediate plate.

  1. for Type A:
    Apply adhesive to 2 or 3 threads of the 2 No. 1 shift detent ball spring seats.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. C295053
    for Type A:
    Using a 6 mm hexagon socket wrench, install the 2 No. 1 shift detent ball spring seats to the intermediate plate.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }

  1. C288240
    for Type B:
    Using a T40 "TORX" socket wrench, install the 2 No. 1 shift detent ball spring seats to the intermediate plate.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }

  1. D025960E02
    Install the detent ball and low side compression spring to the intermediate plate.

  1. for Type A:
    Apply adhesive to 2 or 3 threads of the No. 1 shift detent ball spring seat.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. C295052
    for Type A:
    Using a 6 mm hexagon socket wrench, install the No. 1 shift detent ball spring seat to the intermediate plate.

  1. D029046E02
    for Type B:
    Using a T40 "TORX" socket wrench, install the No. 1 shift detent ball spring seat to the intermediate plate.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }


26. INSTALL TRANSMISSION MAGNET

  1. D025957E02
    Clean the transmission magnet and install it to the intermediate plate.


27. INSTALL MANUAL TRANSMISSION CASE

  1. D029067E16
    Apply seal packing to the manual transmission case as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    Seal diameter:
    1.2 mm (0.0472 in.)

    Text in Illustration 
    *a
    Seal Packing

    NOTICE:
    Assemble parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.

  1. D029117E01
    Place the manual transmission case on wooden blocks.

  1. Using a plastic-faced hammer, tap the intermediate plate to install the manual transmission case.


28. INSTALL NO. 1 COUNTER GEAR FRONT BEARING SNAP RING

  1. D025954E02
    Using a snap ring expander, install the No. 1 counter gear front bearing snap ring to the counter gear front bearing.


29. INSTALL FRONT BEARING SHAFT SNAP RING

  1. D025953E02
    Using a snap ring expander, install the front bearing shaft snap ring to the input shaft front bearing.


30. INSTALL TRANSMISSION FRONT BEARING RETAINER OIL SEAL

  1. C217497E01
    Using SST and a hammer, tap in a new transmission front bearing retainer oil seal to the front bearing retainer.
    SST
    09950-60010   (09951-00300, 09951-00520, 09952-06010)
    09950-70010   (09951-07100)

    Standard oil seal depth:
    11.20 to 12.20 mm (0.441 to 0.480 in.)

  1. Apply a light coat of MP grease to the lip of the transmission front bearing retainer oil seal.


31. INSTALL FRONT BEARING RETAINER

  1. D026036E05
    Apply seal packing to the front bearing retainer as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    Seal diameter:
    1.2 mm (0.0472 in.)

    Text in Illustration 
    *a
    Seal Packing

    NOTICE:
    Assemble parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.

  1. D025950E02
    Install the front bearing retainer to the manual transmission case with the 8 bolts.

    Torque:
    17 N*m{ 168 kgf*cm , 12 ft.*lbf }

  1. Check that the input shaft and output shaft rotate smoothly.


32. INSTALL TRANSFER ADAPTER OIL SEAL

  1. D029118E02
    Using SST and a hammer, tap in a new transfer adapter oil seal to the transfer adapter.
    SST
    09710-30050  
    09950-70010   (09951-07100)

    Standard oil seal depth:
    45.4 to 46.4 mm (1.79 to 1.82 in.)

  1. Apply a light coat of MP grease to the lip of the transfer adapter oil seal.


33. INSTALL REVERSE RESTRICT PIN ASSEMBLY

  1. D029042E02
    Install the reverse restrict pin assembly to the transfer adapter.

  1. D033421E02
    Using a 5 mm pin punch and hammer, tap in the reverse restrict pin slotted spring pin to the transfer adapter.

  1. D029040E02
    Using a T40 "TORX" socket wrench, install the reverse restrict pin plug to the transfer adapter.

    Torque:
    19 N*m{ 189 kgf*cm , 14 ft.*lbf }


34. INSTALL TRANSFER OIL RECEIVER PIPE

  1. D029037E02
    Install the transfer oil receiver pipe to the transfer adapter.


35. INSTALL TRANSFER ADAPTER

  1. D029067E16
    Apply seal packing to the transfer adapter as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    Seal diameter:
    1.2 mm (0.0472 in.)

    Text in Illustration 
    *a
    Seal Packing

    NOTICE:
    Assemble parts within 10 minutes of application. Otherwise, the packing (FIPG) material must be removed and reapplied.

  1. D029119E01
    Using a plastic-faced hammer, tap the transfer adapter to attach it to the manual transmission case.

  1. D029033E03
    Install the transfer adapter to the manual transmission case with the 10 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


36. INSTALL SHIFT AND SELECT LEVER

  1. C216212E01
    Install the shift and select lever with the shift lever housing to the transfer adapter.
    Text in Illustration 
    *1
    Shift Lever Housing
    *2
    Shift and Select Lever

  1. C216209
    Install the bolt to the shift lever housing.

    Torque:
    33 N*m{ 340 kgf*cm , 25 ft.*lbf }


37. INSTALL FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

  1. C216213
    Install the floor shift control shift lever retainer sub-assembly and a new gasket with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


38. INSTALL RESTRICT PIN

  1. C216210
    Install the 2 restrict pins.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


39. INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

  1. D029030E09
    Using SST, install a new gasket and the back-up light switch assembly to the manual transmission case.
    SST
    09817-16011  

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }


40. INSTALL CLUTCH HOUSING

C216208E01
  1. Temporarily install the clutch housing with the 7 bolts labeled A.

  1. Apply adhesive to the 2 bolts labeled B.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Temporarily install the 2 bolts labeled B.

  1. Tighten the 9 bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }


41. INSTALL RELEASE FORK SUPPORT
  1. Install the release fork support to the manual transmission unit.

    Torque:
    47 N*m{ 479 kgf*cm , 34 ft.*lbf }


42. INSTALL CLUTCH RELEASE BEARING ASSEMBLY

C215537E02
  1. Apply release hub grease to the clutch release bearing, and then install it to the clutch release fork with the clip.

    Grease:
    Toyota Genuine Release Hub Grease or equivalent

    Text in Illustration 
    *1
    Release hub grease


43. INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY
  1. Install the clutch release fork.

    NOTICE:
    After the installation, move the fork forward and backward to check that the release bearing slides smoothly.

  1. C215530E01
    Apply clutch spline grease to the spline of the input shaft.

    Grease:
    Toyota Genuine Clutch Spline Grease or equivalent

    Text in Illustration 
    *1
    Clutch spline grease


44. INSTALL CLUTCH RELEASE FORK BOOT
  1. Install the release fork boot to the clutch housing.


45. INSTALL DRAIN PLUG

  1. D029024
    Install a new gasket and the drain plug to the manual transmission case.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


46. INSTALL MANUAL TRANSMISSION FILLER PLUG

  1. D029023E01
    Install a new gasket and the manual transmission filler plug to the manual transmission case.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

← INSPECTION (from Aug 2013)COMPONENTS (from Aug 2013) →