2013-2015 Land Cruiser Prado · Service Manual Audio / Visual / Telematics

INSTALLATION

Removal / installation · Vehicles built from Aug 2013


1. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER

E200376E01

HINT:
Use the same procedure to install the No. 2 ultrasonic sensor retainer on the other side.

  1. Align the keyhole and protrusion as shown in the illustration.

  1. Install the ultrasonic sensor retainer to the front bumper cover.

    NOTICE:
    Do not damage the bumper cover with the protrusion when installing the retainer.

    Text in Illustration 
    *1
    Keyhole


2. INSTALL NO. 1 ULTRASONIC SENSOR

HINT:
Use the same procedure to install the No. 1 ultrasonic sensor on the other side.

  1. Attach the 2 claws to install the No. 1 ultrasonic sensor.

  1. Connect the connector.


3. INSTALL ULTRASONIC SENSOR CLIP

HINT:
Use the same procedure to install the ultrasonic sensor clip on the other side.

  1. Attach the 4 claws to install the ultrasonic sensor clip.


4. INSTALL REAR BUMPER COVER (for 5 Door)
  1. w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Connect the 4 connectors.

  1. w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Connect the 2 connectors.

  1. w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Connect the 2 connectors.

  1. Attach the 14 claws to install the rear bumper cover.

  1. Install the 6 bolts and 2 clips.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


5. INSTALL REAR BUMPER COVER (for 3 Door)
  1. w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Connect the 4 connectors.

  1. w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Connect the 2 connectors.

  1. w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Connect the 2 connectors.

  1. Attach the 10 claws to install the rear bumper cover.

  1. Install the 7 bolts and 2 clips.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


6. INSTALL REAR QUARTER PANEL MUDGUARD LH
  1. Install the rear quarter panel mudguard with the 5 screws and 2 clips.


7. INSTALL REAR QUARTER PANEL MUDGUARD RH

HINT:
Use the same procedure described for the LH side.


8. INSTALL NO. 1 REAR BUMPER PLATE
  1. Attach the 10 claws and 10 guides to install the No. 1 rear bumper plate.


9. INSTALL BACK DOOR CHECK

  1. Bumper side:

    1. B246611E01
      Install the back door check with back door lower damper stay bracket with the 2 bolts labeled A.

      Torque:
      30 N*m{ 306 kgf*cm , 22 ft.*lbf }

    2. Install the bolt labeled B.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    3. Attach the wire harness.

  1. Back door side:

    1. B340680
      Attach the clip to install the back door check with back door lower damper stay bracket.

    2. Install the 2 bolts.

      Torque:
      30 N*m{ 306 kgf*cm , 22 ft.*lbf }


10. INSTALL REAR BUMPER BAR PLATE
  1. Attach the 14 claws to install the rear bumper bar plate.


11. INSTALL JACK BOX HOLE COVER
  1. Attach the 2 claws to install the jack box hole cover.


12. INSTALL PINTLE HOOK ASSEMBLY (w/ Pintle Hook)
  1. Install the pintle hook with the 4 bolts and 4 nuts.

    Torque:
    81 N*m{ 826 kgf*cm , 60 ft.*lbf }

  1. For vehicles with a spare tire installed to the underbody, install the spare tire.

← INSPECTION (from Aug 2013)COMPONENTS (from Aug 2013) →