2013-2015 Land Cruiser Prado · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. REMOVE MANUAL TRANSMISSION FILLER PLUG

  1. D029128E01
    Remove the filler plug and gasket from the manual transmission case.


2. REMOVE DRAIN PLUG SUB-ASSEMBLY

  1. D029129E01
    Remove the drain plug and gasket from the manual transmission case.


3. REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

C215520
  1. Remove the release fork and release bearing from the clutch housing.


4. REMOVE CLUTCH RELEASE BEARING ASSEMBLY

C067602E01
  1. Remove the clip and release bearing from the release fork.


5. REMOVE RELEASE FORK SUPPORT

  1. C086353E01
    Remove the release fork support from the front transmission case.


6. REMOVE CLUTCH RELEASE FORK BOOT

  1. D029348E01
    Remove the clutch release fork boot from the front transmission case.


7. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

  1. D029130E01
    Using SST, remove the back-up light switch and gasket from the manual transmission case.
    SST
    09817-16011  


8. REMOVE FRONT TRANSMISSION CASE

  1. D029131E01
    Remove the 9 bolts.

  1. D029132E01
    Using a plastic-faced hammer, tap off the front transmission case from the manual transmission case.


9. REMOVE RESTRICT PIN

  1. C216025
    Remove the 2 restrict pins from the transfer adapter.


10. REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

  1. C216026
    Remove the 4 bolts from the transfer adapter.

  1. Remove the gasket from the adapter.


11. REMOVE SHIFT DETENT BALL

  1. D029138E05
    Using a T40 "TORX" socket, remove the spring seat from the transfer adapter.

  1. D029139E03
    Using a magnet hand, remove the compression spring and shift detent ball from the transfer adapter.


12. REMOVE TRANSFER ADAPTER

  1. C216028
    Remove the bolt from the shift lever housing.

  1. C145579
    Remove the 8 bolts.

  1. D029137E01
    Using a plastic-faced hammer, tap off the transfer adapter from the manual transmission case.


13. REMOVE TRANSMISSION MAGNET

  1. D029141E01
    Remove the magnet from the transfer adapter.


14. REMOVE TRANSFER OIL RECEIVER PIPE

  1. D029142E01
    Remove the receiver pipe from the transfer adapter.


15. REMOVE SHIFT AND SELECT LEVER

  1. D029143E03
    Remove the shift and select lever and shift lever housing from the transfer adapter.
    Text in Illustration 
    *1
    Shift Lever Housing
    *2
    Shift and Select Lever


16. REMOVE REVERSE RESTRICT PIN ASSEMBLY

  1. D029144E01
    Using a T40 "TORX" socket, remove the plug from the transfer adapter.

  1. D029145E01
    Using a 5 mm pin punch and hammer, tap out the restrict slotted spring pin from the transfer adapter.

  1. D029146E01
    Remove the restrict pin from the transfer adapter.


17. REMOVE TRANSFER ADAPTER OIL SEAL

  1. D029147E01
    Using a screwdriver and hammer, tap out the oil seal from the transfer adapter.

    NOTICE:
    Be careful no to damage the surface which contacts the oil seal.


18. REMOVE FRONT BEARING RETAINER

  1. D029148E01
    Remove the 8 bolts.

  1. Remove the bearing retainer and gasket from the transmission case.


19. REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL

  1. D033559E01
    Using a screwdriver, pry out the oil seal from the front bearing retainer.

    NOTICE:
    Be careful no to damage the surface which contacts the oil seal.


20. REMOVE FRONT BEARING SHAFT SNAP RING

  1. D029149E01
    Using a snap ring expander, remove the snap ring from the input shaft front bearing.


21. REMOVE NO. 1 COUNTER GEAR FRONT BEARING SNAP RING

  1. D029150E01
    Using a snap ring expander, remove the snap ring from the counter gear front bearing.


22. REMOVE MANUAL TRANSMISSION CASE

  1. D033560E01
    Stand the transmission as shown in the illustration.

  1. Using a plastic-faced hammer, carefully tap off the transmission case as shown in the illustration.

  1. Remove the transmission case from the intermediate plate.


23. FIX INTERMEDIATE PLATE

  1. D029152E01
    Fix the intermediate plate in a vise between aluminum plates.


24. REMOVE SHIFT DETENT BALL

  1. D029153E01
    Using a T40 "TORX" socket, remove the spring seat and 2 ball plugs from the intermediate plate.

  1. D029154E01
    Using a magnet hand, remove the 3 compression springs and 3 shift detent balls from the intermediate plate.


25. REMOVE NO. 2 SHIFT DETENT BALL

  1. D029155E01
    Using a T40 "TORX" socket, remove the spring seat from the intermediate plate.

  1. D029156E01
    Using a magnet hand, remove the compression spring and No. 2 detent ball from the intermediate plate.


26. REMOVE NO. 4 GEAR SHIFT FORK SHAFT

  1. D029157E01
    Remove the bolt from the No. 3 gear shift fork.

  1. C216029
    Remove the shift detent ball from the reverse shift head.

  1. C216030
    Remove the No. 4 gear shift fork shaft, shift detent ball and No. 3 gear shift fork from the intermediate plate.


27. REMOVE NO. 5 GEAR SHIFT FORK SHAFT

  1. D029160E01
    Using a 5 mm pin punch and a hammer, tap out the slotted spring pin from the reverse shift head

  1. D029161E01
    Remove the reverse shift head and No. 5 gear shift fork shaft from the intermediate plate.


28. REMOVE NO. 2 SHIFT INTERLOCK PIN

  1. D029162E01
    Using a magnet hand, remove the No. 2 shift interlock pin from the No. 3 gear shift fork shaft.


29. REMOVE NO. 3 GEAR SHIFT FORK SHAFT

  1. C216031
    Using 2 screwdrivers and a hammer, remove the reverse shift head ring from the No. 3 shift fork shaft.

  1. C216032
    Using a 5 mm pin punch and a hammer, tap out the slotted spring pin from the No. 3 shift fork shaft.

  1. C216033
    Remove the No. 3 shift fork shaft from the intermediate plate.


30. REMOVE REVERSE SHIFT ARM

  1. C216034
    Remove the reverse shift arm from the reverse shift arm bracket.

  1. C216035
    Using a screwdriver, remove the reverse shift arm E-ring.

  1. Remove the reverse shift fork from the reverse shift arm.

  1. C216036
    Using a screwdriver, remove the shift arm shoe E-ring.

  1. Remove the shift arm shoe from the reverse shift arm.


31. REMOVE NO. 3 SHIFT INTERLOCK PIN
  1. Using a magnet hand, remove the No. 3 shift interlock pin from the intermediate.


32. REMOVE NO. 2 SHIFT INTERLOCK PIN

  1. D029168E01
    Using a magnet hand, remove the No. 2 shift interlock pin from the No. 1 gear shift fork shaft.


33. REMOVE NO. 1 GEAR SHIFT FORK SHAFT

  1. D029169E01
    Using 2 screwdrivers and a hammer, remove the shaft snap ring from the No. 1 gearshift fork shaft.

  1. D029170E01
    Remove the bolt from the No. 1 gear shift fork.

  1. D029171E01
    Remove the No. 1 gear shift fork shaft from the intermediate plate.


34. REMOVE NO. 1 SHIFT INTERLOCK PIN

  1. D029172E01
    Using a magnet hand, remove the shift interlock pin from the intermediate plate.


35. REMOVE NO. 2 GEAR SHIFT FORK SHAFT

  1. D029173E01
    Remove the bolt from the No. 2 gear shift fork.

  1. D029174E01
    Using 2 screwdrivers and a hammer, remove the shaft snap ring from the No. 2 gear shift fork shaft.

  1. D029175
    Remove the No. 2 gear shift fork shaft, No. 1 gear shift fork and No. 2 gear shift fork from the intermediate plate.


36. INSPECT COUNTER SHAFT 5TH GEAR THRUST CLEARANCE

  1. C086399E01
    Using a feeler gauge, measure the counter shaft 5th gear thrust clearance.

    Standard clearance:
    0.10 to 0.30 mm (0.00394 to 0.0118 in.)

    1. If the result is not as specified, replace the counter shaft 5th gear.


37. REMOVE COUNTER SHAFT 5TH GEAR

  1. C216038
    Using 2 screwdrivers and a hammer, tap out the counter gear rear shaft snap ring from the counter gear.

  1. C216217E01
    Using SST, remove the No. 5 gear spline and the No. 1 synchronizer ring from the counter gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)

  1. D029178E01
    Remove the counter shaft 5th gear and the counter 5th gear bearing from the counter gear.


38. REMOVE NO. 3 TRANSMISSION HUB SLEEVE

  1. C216063E01
    Remove the No. 3 transmission hub sleeve, 2 synchromesh shifting key springs, 3 synchromesh shifting keys, counter 5th gear bearing and counter shaft 5th gear.
    Text in Illustration 
    *1
    No. 3 Transmission Hub Sleeve
    *2
    No. 3 Synchromesh Shifting Key Spring
    *3
    Counter 5th Gear Bearing
    *4
    No. 3 Synchromesh Shifting Key
    *5
    Counter Shaft 5th Gear


39. REMOVE 5TH GEAR THRUST WASHER

  1. D029179E01
    Remove the 5th gear thrust washer from the counter gear.


40. REMOVE 5TH GEAR BEARING INNER RACE LOCK BALL

  1. D029180E01
    Using a magnet hand, remove the 5th gear bearing inner race lock ball from the counter gear.


41. REMOVE REVERSE SHIFT ARM BRACKET

  1. C216039
    Remove the 2 bolts and reverse shift arm bracket from the intermediate plate.


42. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY

  1. C216040
    Remove the bolt and reverse idler gear shaft stopper from the intermediate plate.

  1. D033543E05
    Remove the reverse idler gear shaft and the reverse idler gear from the intermediate plate.


43. INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE

  1. C086408E01
    Using a dial indicator, measure the reverse idler gear radial clearance.

    Standard clearance:
    0.04 to 0.08 mm (0.00158 to 0.00314 in.)

    Maximum clearance:
    0.08 mm (0.00314 in.)

    1. If the clearance is more than the maximum, replace the needle roller bearing.


44. INSPECT REVERSE IDLER GEAR SUB-ASSEMBLY

  1. C086409
    Using a feeler gauge, measure the clearance between the reverse idler gear and the shift arm shoe.

    Standard clearance:
    0.05 to 0.28 mm (0.00197 to 0.0110 in.)

    Maximum clearance:
    0.28 mm (0.00110 in.)

    1. If the clearance is more than the maximum, replace the reverse idler gear and reverse shift arm.


45. REMOVE OUTPUT SHAFT REAR BEARING RETAINER

  1. D029184E01
    Using a T40 "TORX" socket wrench, remove the 4 screws and output shaft rear bearing retainer from the intermediate plate.


46. REMOVE COUNTER GEAR ASSEMBLY

  1. D029185E01
    Using a snap ring expander, remove the counter shaft center bearing snap ring from the counter shaft center bearing.

  1. C216218E01
    Using SST, remove the counter shaft center bearing and counter gear from the intermediate plate.
    SST
    09950-40011   (09951-04010, 09952-04010, 09953-04010, 09954-04010, 09955-04011, 09958-04011)


47. REMOVE INPUT SHAFT ASSEMBLY

  1. C216043
    Remove the input shaft with the 13 input shaft bearings and No. 2 synchronizer ring from the output shaft.


48. REMOVE OUTPUT SHAFT ASSEMBLY

  1. D029187E01
    Using a snap ring expander, remove the output shaft bearing shaft snap ring from the output shaft bearing.

  1. C216044
    Remove the output shaft from the intermediate plate by pulling on the output shaft and tapping on the intermediate plate with a plastic-faced hammer.

← COMPONENTS (from Aug 2013)INSPECTION (from Aug 2013) →