2013-2015 Land Cruiser Prado · Service Manual General

TORQUE SPECIFICATIONS

Specifications · Vehicles built from Aug 2013

ENGINE 
Part Tightened
N*m
kgf*cm
ft.*lbf
Intake air connector x Cylinder head cover
8.0
82
71 in.*lbf
Intake air connector hose clamp
5.0
51
44 in.*lbf
Spark plug x Cylinder head
18
184
13
Ignition coil x Cylinder head cover
9.0
92
80 in.*lbf
DRIVE BELT 
Part Tightened
N*m
kgf*cm
ft.*lbf
Tensioner pulley x Tensioner arm
50
510
37
CAMSHAFT 
Part Tightened
N*m
kgf*cm
ft.*lbf
Camshaft timing gear x Camshaft
78
795
58
Camshaft bearing cap x Cylinder head
bolt A
12
122
9
except bolt A
16
158
11
Camshaft timing sprocket x No. 2 camshaft
78
795
58
Straight screw plug x Timing chain cover
17
169
12
Timing chain guide x No. 1 camshaft bearing cap
10
102
7
CYLINDER HEAD GASKET 
Part Tightened
N*m
kgf*cm
ft.*lbf
Cylinder head x Cylinder block
1st
39
398
29
2nd
Turn 90°
Turn 90°
Turn 90°
3rd
Turn 90°
Turn 90°
Turn 90°
Camshaft bearing cap x Cylinder head
bolt A
12
122
9
except bolt A
16
158
11
No. 1 chain vibration damper x Cylinder block, Cylinder head
bolt
21
214
15
nut
18
184
13
Chain tensioner slipper x Cylinder block
21
214
15
No. 1 chain tensioner x Cylinder block
10
102
7
FRONT CRANKSHAFT OIL SEAL 
Part Tightened
N*m
kgf*cm
ft.*lbf
Crankshaft pulley x Crankshaft
260
2651
192
REAR CRANKSHAFT OIL SEAL 
Part Tightened
N*m
kgf*cm
ft.*lbf
Drive plate and ring gear x Crankshaft
for Automatic Transmission
74
755
55
Flywheel x Crankshaft
for manual Transmission
1st
27
270
20
2nd
Turn 90°
Turn 90°
Turn 90°
ENGINE ASSEMBLY 
Part Tightened
N*m
kgf*cm
ft.*lbf
No. 1 engine hanger x Cylinder head
42
428
31
Engine mounting insulator x Body
40
408
30
Rear end plate x Cylinder block, No. 1 water by-pass pipe
bolt A
18
184
13
bolt B
18
178
13
Rear no. 1 engine mounting insulator x Transmission
65
663
48
Rear engine mounting heat insulator x Rear no. 1 engine mounting insulator
12
122
9
No. 3 frame crossmember x Rear no. 1 engine mounting insulator
30
306
22
Front engine mounting insulator LH x harness bracket
13
131
9
Wire harness x Relay block
11
112
8
Ground wire x Cylinder block
22
219
16
Cooler compressor x No. 1 compressor mounting bracket
25
250
18
Suction hose x Timing chain cover
7.8
80
69 in.*lbf
Vane pump x Timing chain cover
21
214
15
Pressure feed tube x Body
28
285
21
Air cleaner case x Body
12
122
9
Air cleaner cap hose clamp
5.0
51
44 in.*lbf
Ground wire x Body
8.5
87
75 in.*lbf
Hood Body
bolt A
13
133
10
bolt B
18
184
13
Rear engine under cover x Body
29
296
21
Transmission under cover x Rear engine under cover
29
296
21
No. 1 engine under cover x Body
29
296
21
Front bumper cover lower x Body
8.0
82
71 in.*lbf
ENGINE UNIT 
Part Tightened
N*m
kgf*cm
ft.*lbf
No. 4 chain vibration damper x Cylinder block
18
184
13
Balance shaft drive gear x No. 1 balance shaft
25
255
18
No. 2 chain tensioner x Cylinder block
18
184
13
No. 3 chain vibration damper x Cylinder block
18
184
13
No. 2 chain vibration damper x Cylinder block
27
270
20
No. 1 taper screw plug x Cylinder block
25
250
18
Oil filter bracket union x Cylinder block
25
250
18
Oil filter bracket x Screw plug
49
500
36
Oil filter bracket x Cylinder block
25
255
18
Oil filter union x Oil filter bracket
43
439
32
Oil seal retainer x Cylinder block
13
133
10
Oil control valve filter screw plug x Cylinder head
30
306
22
Camshaft timing sprocket x No. 2 camshaft
78
795
58
Straight screw plug x Timing chain cover
17
169
12
Oil pan stud bolt
Stud bolt A
7.5
76
66 in.*lbf
Stud bolt A
3.0
31
27 in.*lbf
Front no. 1 engine mounting bracket RHx Cylinder block
51
520
38
Front no. 1 engine mounting bracket LHx Cylinder block
51
520
38
Front engine mounting insulator x Front no. 1 engine mounting bracket
46
469
34
Engine oil lever dipstick guide x Front no. 1 engine mounting bracket
20
204
15
No. 1 water by-pass pipe x Timing chain cover
18
178
13
No. 1 compressor mounting bracket x Cylinder block
for bolt B
45
459
33
for bolt A
45
459
33
for bolt C
25
250
18
Idle pulley assembly x No. 1 compressor mounting bracket
44
449
32
CYLINDER HEAD 
Part Tightened
N*m
kgf*cm
ft.*lbf
Stud bolt
Stub bolt A
3.0
31
27 in.*lbf
Stub bolt B
7.5
76
66 in.*lbf
Stub bolt C
7.5
76
66 in.*lbf
No. 1 head straight screw plug x Cylinder head
44
449
32
No. 2 head straight screw plug x Cylinder head
140
1428
103
CYLINDER BLOCK 
Part Tightened
N*m
kgf*cm
ft.*lbf
Stud bolt
Stud bolt A
7.5
76
66 in.*lbf
Stud bolt B and D
7.5
76
66 in.*lbf
Stud bolt C
7.5
76
66 in.*lbf
Cylinder block water drain cock x Cylinder block
25
250
18
Water drain cock plug x Cylinder block water drain cock
13
130
9
No. 1 oil nozzle x Cylinder block
7.0
71
62 in.*lbf
No. 2 balance shaft drive gear x No. 2 balance shaft
36
367
27
No. 2 balance shaft x Cylinder block
18
184
13
No. 1 balance shaft drive gear x No. 1 balance shaft
36
367
27
No. 1 balance shaft x Cylinder block
18
184
13
Crankshaft Cylinder block
1st
39
398
29
2nd
Turn 90°
Turn 90°
Turn 90°
Connecting rod x Connecting rod cap
1st
25
250
18
2nd
Turn 90°
Turn 90°
Turn 90°
← SERVICE DATA (from Aug 2014)SERVICE DATA (Aug 2013 – Jul 2014) →