2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built from Aug 2013

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.


1. INSTALL REAR SEATBACK HEATER ASSEMBLY

B248650E02
  1. Set the rear seatback heater assembly in place with the name stamp side facing the separate type rear seatback cover.

    Text in Illustration 
    *1
    Tack Pin
    *2
    Name Stamp

  1. Install the rear seatback heater assembly with 11 new tack pins.


2. INSTALL SEPARATE TYPE REAR SEATBACK COVER
  1. Set the separate type rear seatback cover in place.

  1. B241214E01
    Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 8 new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the separate type rear seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

  1. B248338
    w/ Seat Heater System:

    1. Connect the rear seatback heater assembly wire harness to the separate type rear seatback pad.


3. INSTALL SEATBACK COVER WITH PAD

  1. w/ Seat Heater System:

    1. B360128E01
      Install the wire harness as shown in the illustration.
      Text in Illustration 
      *a
      Paint Mark

  1. B237917E01
    Attach the hooks.
    Text in Illustration 
    *1
    Hog Ring Pliers
    *2
    Hook
    *3
    Hog Ring

  1. Using hog ring pliers, install the seatback cover with pad with 14 new hog rings.

    NOTICE:
    1. Be careful not to damage the separate type rear seatback cover.
    2. Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.


4. INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
  1. Attach the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.


5. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY RH
  1. Attach the 7 clips to install the rear seatback board carpet assembly RH.


6. INSTALL REAR SEATBACK COVER
  1. Attach the 4 claws to install the rear seatback cover.


7. INSTALL REAR CENTER BACK LOCK CONTROL LEVER

B237946
  1. Attach the cable clamp to connect the cable to the rear center back lock control lever.

  1. Move the rear center back lock control lever in the direction of the arrow to attach the guide.

  1. Install the rear center back lock control lever with the 2 screws.


8. INSTALL REAR SEAT COVER CAP
  1. Attach the guide and claw to install the rear seat cover cap.


9. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH

  1. B165053E02
    Connect the cable in the order shown in the illustration to install the rear seat lock control lever sub-assembly RH.

  1. Install the 2 screws.


10. INSTALL RECLINING ADJUSTER KNOB CAP RH

B237755
  1. Attach the guide and claw to install the reclining adjuster knob cap RH.


11. INSTALL SEAT CUSHION COVER WITH PAD

  1. w/ Seat Heater System:

    1. B360129
      Pass the wire harness as shown in the illustration.

    2. B359311
      Connect the 2 rear seat heater connectors.

  1. B237910
    Attach the hooks to install the seat cushion cover with pad.


12. INSTALL REAR SEAT REAR CUSHION MOULDING LH
  1. Attach the 2 guides and 3 claws to install the rear seat rear cushion moulding LH.

  1. Install the screw.


13. INSTALL REAR SEAT CUSHION MOULDING RH

B237717
  1. Move the rear seat cushion moulding RH in the direction of the arrow to attach the guide and install the rear seat cushion moulding RH.

  1. Attach the 3 claws and clip to install the rear seat cushion moulding RH.


14. INSTALL RECLINING ADJUSTER RELEASE HANDLE RH
  1. Install the reclining adjuster release handle RH with the 3 screws.


15. INSTALL REAR SEAT UPPER RECLINING COVER RH

B237787
  1. Attach the 3 claws to install the rear seat upper reclining cover RH.


16. INSTALL REAR NO. 1 SEAT ASSEMBLY RH
(Click here)
← INSPECTION (from Aug 2013)COMPONENTS (Aug 2013 – Jul 2014) →