CUSTOMIZE PARAMETERS
Removal / installation · Vehicles built from Aug 2013
| 1. CUSTOMIZE TOYOTA PARKING ASSIST-SENSOR SYSTEM |
- HINT:
- The following items can be customized.
- NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
- When the customer requests a change in a function, first make sure that the function can be customized.
Customizing with the GTS
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Customize Setting / Clearance Sonar / Warning, Sensor or Display.
Select the setting by referring to the table below.
Warning Display
Default
Content
Setting
Relevant ECU
Rr Sensor Onset Range
Wide
Set the buzzer activation range for the rear center sensors.
Narrow or Wide - Narrow: 650 mm (25.6 in.)
- Wide: 1500 mm (59.1 in.)
Clearance warning ECU
Fr Sensor Onset Range
Wide
Set the buzzer activation range for the front center sensors.
Narrow or Wide - Narrow: 600 mm (23.6 in.)
- Wide: 1000 mm (39.4 in.)
Clearance warning ECU
Keep Sense Buzzer
Avail
Make the buzzer sound when the distance between the vehicle and obstacle does not change for more than 3 seconds.
Not Avail or Avail - Not Avail: Not Available
- Avail: Available
Clearance warning ECU
Fr & Rr Buzzer Volume
M2
Change the buzzer volume setting.
L, M1, M2, M3 or H - L: Low volume
- M1: Medium low volume
- M2: Medium volume
- M3: Medium high volume
- H: High volume
Clearance warning ECU
Sensor Condition N
Avail
Make the front sensors available when the shift lever is in N.
Not Avail or Avail - Not Avail: Not Available
- Avail: Available
Clearance warning ECU
Reverse Range Front Sensor
Fcrn
Change the operation setting for the front sensors when the shift lever is in R.
F, Fcrn or F Stop - F: Front sensors are available
- Fcrn: Front corner sensors are available
- F Stop: Front sensors are not available
Clearance warning ECU
Non P/R Range Rear Sensor
R Stop
Change the operation setting for the rear sensors when the shift lever is in any position except P or R.
R, Rcrn or R Stop - R: All rear sensors are available
- Rcrn: Rear corner sensors are available
- R Stop: All rear sensors are not available
Clearance warning ECU
Display Mode
All
Change the display mode setting (when the TOYOTA parking assist-sensor system is normal).
All or Undisp
Clearance warning ECU
- Narrow: 650 mm (25.6 in.)
Customizing with Multi-display
Turn the engine switch on (IG).
Enter the following menus: Setup / Vehicle / TOYOTA Park Assist.
Select the setting by referring to the table below.
Display
Default
Content
Setting
Relevant
Alert volume
3
Change the buzzer volume setting.
1, 2, 3, 4 or 5 - 1: Low volume
- 2: Medium low volume
- 3: Medium volume
- 4: Medium high volume
- 5: High volume
Clearance warning ECU
Display
On
Change the display mode setting (when the TOYOTA parking assist-sensor system is normal).
On or Off
Clearance warning ECU
Distance
Wide
Set the buzzer activation range for the front center sensors.
Narrow or Wide - Narrow: 600 mm (23.6 in.)
- Wide: 1000 mm (39.4 in.)
Clearance warning ECU
Set the buzzer activation range for the rear center sensors.
Narrow or Wide - Narrow: 650 mm (25.6 in.)
- Wide: 1500 mm (59.1 in.)
Clearance warning ECU
- 1: Low volume
