2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0522 Engine Oil Pressure Sensor / Switch Low

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Also covers:

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTC P0524 (Click here)
P0522 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 5 second
Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic):
(a) Engine switch is on (IG).
(b) Oil pressure sender gauge assembly voltage is 0.5 V or less.
  1. Open or short in oil pressure sender gauge assembly circuit
  2. Oil pressure sender gauge assembly
  3. ECM
P0523 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 5 second
Conditions (a) and (b) continue for 0.5 seconds or more (1 trip detection logic):
(a) Engine switch is on (IG).
(b) Oil pressure sender gauge assembly voltage is 4.6 V or higher.
  1. Open or short in oil pressure sender gauge assembly circuit
  2. Oil pressure sender gauge assembly
  3. ECM
Related Data List 
DTC No.
Data List
P0522
P0523
Engine Oil Pressure

WIRING DIAGRAM

A311398E01

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR
  1. Disconnect the oil pressure sender gauge assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C123-3 (VC) - C91-13 (VCPX)
    Always
    Below 1 Ω
    C123-2 (VOUT) - C91-4 (POP)
    Always
    Below 1 Ω
    C123-1 (GND) - C91-14 (EPEX)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C123-3 (VC) or C91-13 (VCPX) - Body ground
    Always
    10 kΩ or higher
    C123-2 (VOUT) or C91-4 (POP) - Body ground
    Always
    10 kΩ or higher
    C123-1 (GND) or C91-14 (EPEX) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


2. CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)

  1. A241069E01
    Disconnect the oil pressure sender gauge assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C123-3 (VC) - Body ground
    Engine switch on (IG)
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Oil Pressure Sender Gauge Assembly)

  1. Reconnect the oil pressure sender gauge assembly connector.



NG
Go to step 5
OK


3. REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY
  1. Replace the oil pressure sender gauge assembly (Click here).


NEXT


4. CHECK WHETHER DTC OUTPUT RECURS (P0522 AND/OR P0523)
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off for 30 seconds or more.

  1. Turn the engine switch on (IG) and start the engine.

  1. Start the engine and idle it for 5 second or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0522 or P0523 is output
    A
    No DTC is output
    B



B
END
A


5. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch off for 30 seconds or more.

  1. Turn the engine switch on (IG) and start the engine.

  1. Start the engine and idle it for 5 second or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0504 Brake Switch "A" / "B" Correlation (from Aug 2014)P0522 Engine Oil Pressure Sensor / Switch Low (+ P0523) (from Aug 2014) →