P052F Glow Plug Control Module System Voltage
Diagnostic trouble codes · Vehicles built from Aug 2014
Also covers:
- P0683 Glow Plug Control Module to PCM Communication Circuit
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The glow system consists of the glow plug controller, glow plugs and ECM. The glow plug controller turns on the glow plug of each cylinder according to the duty command signal from the ECM in order to maintain optimal engine temperatures. The glow plugs can be controlled according to the engine coolant temperature at engine start by using duty signals. This helps induce ignition under low temperatures and prevent rough idle after starting the engine.The glow plugs are turned on during catalyst regeneration in order to prevent the engine speed from rising due to an increase in fuel injection volume used to increase the exhaust gas temperature. The glow plug controller contains a self-diagnosis function. When the glow plug controller detects an internal malfunction, it sends a signal indicating the malfunction to the ECM. When the ECM receives this signal, it illuminates the MIL and stores a DTC.
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Enter check mode |
The glow plug controller recognizes the battery voltage as being 18.4 V or higher 3 times or more when the glow plugs are on (2 trip detection logic). |
Glow plug controller |
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Enter check mode |
When the glow plugs are on, the ECM detects that there is no output from the glow plug control unit for 3 seconds even though the ECM outputs an SI signal ("ON" command signal) (1 trip detection logic). |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
P0683 is output
A
P052F is output
B
|
|
||||
| A | |
| 2. CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT) |
Disconnect the glow plug controller connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A83-4 (+B) - Body ground
Engine switch on (IG)
11 to 14 V
A83-4 (+B) - Body ground
Engine switch off
Below 0.5 V
Text in Illustration *a
Front view of wire harness connector
(to Glow Plug Controller)
Reconnect the glow plug controller connector.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND) |
Disconnect the glow plug controller connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
A83-1 (GND) - Body ground
Always
Below 1 Ω
Reconnect the glow plug controller connector.
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM) |
Disconnect the glow plug controller connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
A83-3 (SI) - C91-20 (GLDO)
Always
Below 1 Ω
A83-5 (DI) - C91-21 (GLDI)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
A83-3 (SI) or C91-20 (GLDO) - Body ground
Always
10 kΩ or higher
A83-5 (DI) or C91-21 (GLDI) - Body ground
Always
10 kΩ or higher
Reconnect the glow plug controller connector.
Reconnect the ECM connector.
|
|
||||
|
|
||||
| 5. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - NO. 1 INTEGRATION RELAY) |
Disconnect the glow plug controller connector.
Remove the No. 1 integration relay from the No. 2 relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
A83-4 (+B) - 1B-8
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
A83-4 (+B) or 1B-8 - Body ground
Always
10 kΩ or higher
Reconnect the glow plug controller connector.
Reinstall the No. 1 integration relay
|
|
||||
| OK | |
| 6. CHECK CHARGING SYSTEM |
Check the charging system and perform repairs as necessary (Click here).
|
|
||||
| 7. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
|
||||
| 8. REPLACE GLOW PLUG CONTROLLER |
Replace the glow plug controller (Click here).
| NEXT | |
| 9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG).
Turn the tester on.
Using the intelligent tester, switch the ECM from normal mode to check mode (Click here).
Confirm that the DTC is not output again.
- HINT:
- Check for DTCs in check mode.
|
|
||||
| OK | ||
| ||
| 10. REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG).
Turn the tester on.
Using the intelligent tester, switch the ECM from normal mode to check mode (Click here).
Confirm that the DTC is not output again.
- HINT:
- Check for DTCs in check mode.
| NEXT | ||
| ||
| 12. REPLACE GLOW PLUG CONTROLLER |
Replace the glow plug controller (Click here)
| NEXT | |
| 13. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG).
Turn the tester on.
Using the intelligent tester, switch the ECM from normal mode to check mode (Click here).
Confirm that the DTC is not output again.
- HINT:
- Check for DTCs in check mode.
| NEXT | ||
| ||
