2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

U1002 Lost Communication with Gateway Module

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

  1. The network gateway ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN V2 bus.
  2. When the network gateway ECU receives a response signal from the ECUs connected to the CAN V2 bus, the network gateway ECU recognizes and memorizes that the ECU is connected to the CAN V2 bus. Based on this memorized data, the network gateway ECU monitors for malfunctions in the ECUs connected to the CAN V2 bus when communicating with those ECUs. If the network gateway ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN V2 bus, the network gateway ECU determines that a malfunction exists.
  3. If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
DTC Code
DTC Detection Condition
Trouble Area
U1002
Lost communication with the gateway module.
  1. V2 bus circuit
  2. Network gateway ECU CAN main wire or connector
  3. Clearance warning ECU assembly CAN branch wire or connector*1
  4. Headlight swivel ECU assembly CAN branch wire or connector*2
  5. Network gateway ECU
  6. Clearance warning ECU assembly*1
  7. Headlight swivel ECU assembly*2
  8. No. 1 junction connector
  9. No. 3 junction connector
  10. No. 5 junction connector
  11. No. 7 junction connector
  1. For vehicles with a network gateway ECU.
  2. *1: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type)
  3. *2: for LED Headlight

WIRING DIAGRAM

C294452E01

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

    NOTICE:
    1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
    2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK CAN BUS WIRE (CHECK CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)

  1. C242747E09
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance: Malfunction
    G155-13 (CA2H) - G155-12 (CA2L)
    Ignition switch off
    54 to 69 Ω
    Below 53 Ω: Short in line
    G155-13 (CA2H) - G155-12 (CA2L)
    Ignition switch off
    54 to 69 Ω
    Higher than 70 Ω: Open in CAN main bus line
    G155-13 (CA2H) - G155-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    G155-12 (CA2L) - G155-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    G155-13 (CA2H) - G155-4 (GND)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    G155-12 (CA2L) - G155-4 (GND)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short

    Text in Illustration 
    *a
    Component with harness connected
    (Network Gateway ECU)
    Result 
    Result
    Proceed to
    NG
    1. Open in CAN main bus line
    A
    NG
    1. Short in line
    2. +B short
    3. GND short
    B
    OK
    C



B
Go to step 15

C
Go to step 33
A


3. CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. C242748E58
    Disconnect the G95 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G95-1 (CANH) - G95-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 5
OK


4. CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

  1. C242748E59
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G95-3 (CANH) - G95-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 10
OK

REPLACE NO. 3 JUNCTION CONNECTOR

5. CONNECT CONNECTOR
  1. Reconnect the G95 No. 3 junction connector.


NEXT


6. CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. C242748E60
    Disconnect the G98 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G98-1 (CANH) - G98-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 8
OK


7. CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. C242748E61
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G98-3 (CANH) - G98-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE NO. 1 JUNCTION CONNECTOR

8. CONNECT CONNECTOR
  1. Reconnect the G98 No. 1 junction connector.


NEXT


9. CHECK FOR OPEN IN CAN BUS WIRE (NETWORK GATEWAY ECU)

  1. C242749E24
    Disconnect the G155 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G155-13 (CA2H) - G155- 12 (CA2L)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Network Gateway ECU)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (NETWORK GATEWAY ECU - NO. 1 JUNCTION CONNECTOR)
OK

REPLACE NETWORK GATEWAY ECU (Click here)

10. CONNECT CONNECTOR
  1. Reconnect the G95 No. 3 junction connector.


NEXT


11. CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

  1. C292202E09
    Disconnect the A73 No. 5 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-1 (CANH) - A73-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)



NG
Go to step 13
OK


12. CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. C292202E10
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-2 (CANH) - A73-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK

REPLACE NO. 5 JUNCTION CONNECTOR

13. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


14. CHECK FOR OPEN IN CAN BUS WIRE (NO. 7 JUNCTION CONNECTOR)

  1. C242676E04
    Disconnect the G102 No. 7 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G102-3 (CANH) - G102-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 7 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK

REPLACE NO. 7 JUNCTION CONNECTOR

15. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR SIDE)

  1. C242747E09
    Disconnect the A73 No. 5 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G155-13 (CA2H) - G155-12 (CA2L)
    Ignition switch off
    108 to 132 Ω
    G155-13 (CA2H) - G155-4 (GND)
    Ignition switch off
    200 Ω or higher
    G155-12 (CA2L) - G155-4 (GND)
    Ignition switch off
    200 Ω or higher
    G155-13 (CA2H) - G155-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    G155-12 (CA2L) - G155-2 (BATT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Network Gateway ECU)



NG
Go to step 22
OK


16. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - HEADLIGHT SWIVEL ECU ASSEMBLY)

NOTICE:
For vehicles with a halogen headlight, go to "Check for Short in CAN Bus Wires (No. 5 Junction Connector - No. 7 Junction Connector)".

  1. C294654E43
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-4 (CANH) - A73-15 (CANL)
    Ignition switch off
    200 Ω or higher
    A73-4 (CANH) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    A73-15 (CANL) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    A73-4 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A73-15 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 18
OK


17. CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR - NO. 7 JUNCTION CONNECTOR)

  1. C294654E42
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A73-1 (CANH) - A73-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    A73-1 (CANH) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    A73-12 (CANL) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    A73-1 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A73-12 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 5 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 20
OK

REPLACE NO. 5 JUNCTION CONNECTOR

18. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


19. CHECK FOR SHORT IN CAN BUS WIRES (HEADLIGHT SWIVEL ECU ASSEMBLY)

  1. C217420E01
    Disconnect the A58 headlight swivel ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A58-12 (CANH) - A58-13 (CANL)
    Ignition switch off
    54 to 69 Ω
    A58-12 (CANH) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    A58-13 (CANL) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    A58-12 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A58-13 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Headlight Swivel ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT SWIVEL ECU ASSEMBLY (CANH, CANL)
OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)

20. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


21. CHECK FOR SHORT IN CAN BUS WIRES (NO. 7 JUNCTION CONNECTOR)

  1. C242753E05
    Disconnect the G102 No. 7 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G102-3 (CANH) - G102-2 (CANL)
    Ignition switch off
    108 to 132 Ω
    G102-3 (CANH) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    G102-2 (CANL) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    G102-3 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G102-2 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 7 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 7 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK

REPLACE NO. 7 JUNCTION CONNECTOR

22. CONNECT CONNECTOR
  1. Reconnect the A73 No. 5 junction connector.


NEXT


23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

  1. C288300E07
    Disconnect the G95 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G95-3 (CANH) - G95-14 (CANL)
    Ignition switch off
    108 to 132 Ω
    G95-3 (CANH) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    G95-14 (CANL) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    G95-3 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G95-14 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
OK


24. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR SIDE)

  1. C242747E09
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G155-13 (CA2H) - G155-12 (CA2L)
    Ignition switch off
    108 to 132 Ω
    G155-13 (CA2H) - G155-4 (GND)
    Ignition switch off
    200 Ω or higher
    G155-12 (CA2L) - G155-4 (GND)
    Ignition switch off
    200 Ω or higher
    G155-13 (CA2H) - G155-2 (BATT)
    Ignition switch off
    6 kΩ or higher
    G155-12 (CA2L) - G155-2 (BATT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Network Gateway ECU)



NG
Go to step 25
OK

REPLACE NO. 3 JUNCTION CONNECTOR

25. CONNECT CONNECTOR
  1. Reconnect the G95 No. 3 junction connector.


NEXT


26. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. C288300E08
    Disconnect the G98 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G98-3 (CANH) - G98-14 (CANL)
    Ignition switch off
    108 to 132 Ω
    G98-3 (CANH) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    G98-14 (CANL) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    G98-3 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G98-14 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK


27. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)

  1. C294654E44
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G98-2 (CANH) - G98-13 (CANL)
    Ignition switch off
    200 Ω or higher
    G98-2 (CANH) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    G98-13 (CANL) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    G98-2 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G98-13 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 29
OK


28. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. C288300E10
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G98-1 (CANH) - G98-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    G98-1 (CANH) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    G98-12 (CANL) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    G98-1 (CANH) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G98-12 (CANL) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 31
OK

REPLACE NO. 1 JUNCTION CONNECTOR

29. CONNECT CONNECTOR
  1. Reconnect the G98 No. 1 junction connector.


NEXT


30. CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)

  1. C266899E07
    Disconnect the I1 clearance warning ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    I1-3 (R1) - I1-5 (R2)
    Ignition switch off
    54 to 69 Ω
    I1-3 (R1) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    I1-5 (R2) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    I1-3 (R1) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    I1-5 (R2) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Clearance Warning ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU ASSEMBLY (R1, R2)
OK

REPLACE CLEARANCE WARNING ECU ASSEMBLY (Click here)

31. CONNECT CONNECTOR
  1. Reconnect the G98 No. 1 junction connector.


NEXT


32. CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)

  1. C242755E05
    Disconnect the G155 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    G155-13 (CA2H) - G155-12 (CA2L)
    Ignition switch off
    108 to 132 Ω
    G155-13 (CA2H) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    G155-12 (CA2L) - G48-4 (CG)
    Ignition switch off
    200 Ω or higher
    G155-13 (CA2H) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    G155-12 (CA2L) - G48-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Network Gateway ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (CA2H, CA2L)
OK

REPLACE NETWORK GATEWAY ECU (Click here)

33. CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)

  1. C242749E25
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the G155 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G155-4 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G155-2 (BATT) - Body ground
    Always
    11 to 14 V
    G155-10 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V
    G155-9 (IG2) - Body ground
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Rear view of wire harness connector
(to Network Gateway ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE NETWORK GATEWAY ECU (Click here)


← U0182 Lost Communication with AFS ECU (from Aug 2014)U1002 Lost Communication with Gateway Module (from Aug 2014) →