Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR(for 3 Door)
BM27T0E _01 Vehicle Exterior _054380 BODY WELD POINT _0264636 CENTER BODY PILLAR(for 3 Door) F

BODY WELD POINT  CENTER BODY PILLAR(for 3 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K132813

Weld work for 980 MPa ultra high strength steel


1.

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

*a: When welding 2 panels together including 980 MPa ultra high strength steel.

Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 18 Cyc. (0.30 Sec.)
Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

*b: When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a panel to the welded panels with the weld condition above.)

Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

HINT:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



With the cowl top side panel removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location

REMOVAL POINT
1.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)

2.

*c indicates welds to remove for easier removal.

3.

After removing the *d, remove the *e.

4.

*f and*g indicates the location of the foamed sealing material. Be careful when cutting as the foamed sealing

5.

Remove the remaining foamed sealing material from the vehicles side.

6.

*h is reused.


K132838C01
1.219,1.344 0.896,0.854 false 1.625,1.354 1.365,0.729 false 2.229,1.292 2.458,0.74 false 6.625,8.49 6.938,8.646 0.313,0.156 10 false *k 2.917,6.802 3.229,7 0.313,0.198 10 false *c 4.333,7.948 4.646,8.146 0.313,0.198 10 false *c 5.635,7.542 5.948,7.74 0.313,0.198 10 false *c 2.813,0.979 4.188,1.177 1.375,0.198 10 false 20 (0.79) 0.615,2.083 1.333,2.292 0.719,0.208 10 false 245 (9.65) 2.385,1.958 3.104,2.167 0.719,0.208 10 false 175 (6.89) 0.771,0.667 1.083,0.865 0.313,0.198 10 false *f 1.26,0.542 1.573,0.74 0.313,0.198 10 false *h 2.417,0.552 2.729,0.75 0.313,0.198 10 false *g
*k mm (in.) - -


K132839N01
1.729,2.021 2.344,1.76 false 1.229,4.125 1.542,3.438 false 1.135,4.167 1.448,4.365 0.313,0.198 10 false *e 2.406,1.667 2.719,1.865 0.313,0.198 10 false *d


INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108824

Plug Weld
K108830

Fillet Weld
K108831

Butt Weld

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

Follow the welding conditions when welding point *a to assure sufficient weld strength. (See the introduction)

4.

*I indicates the location of the foamed sealing material. Be careful when welding as the foamed sealing material is located near the area that is cut and joined together.

5.

After welding the center body inner pillar and center body pillar upper reinforce to the vehicle side, install the center body outer pillar and *j.

6.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

7.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.

9.

After welding the center body inner pillar to the vehicle side, install the center body pillar upper reinforce.


K132840C01
4.292,5.229 5.083,5.063 false 4.052,5.167 4.365,5.323 0.313,0.156 10 false *1 6.573,8.49 6.885,8.646 0.313,0.156 10 false *k 6.292,5.667 6.604,5.865 0.313,0.198 10 false *a 0.865,3.854 1.177,4.052 0.313,0.198 10 false *a 0.552,2.635 0.865,2.833 0.313,0.198 10 false *a 4.646,6.969 5.281,7.25 0.635,0.281 10 false 50 (1.97) 5.802,6.979 6.438,7.26 0.635,0.281 10 false 50 (1.97)
*1 Center Body Inner Pillar - -
*k mm (in.) - -


K132841C01
4.24,3.25 5.552,4.26 false 4.521,5.885 4.823,6.229 false 5.104,5.875 5.302,6.313 false 5.635,4.24 5.948,4.396 0.313,0.156 10 false *1 1.156,1.792 1.469,1.99 0.313,0.198 10 false *a 1.313,2.865 1.625,3.063 0.313,0.198 10 false *a 3.438,4 3.75,4.198 0.313,0.198 10 false *a 4.365,5.688 4.677,5.885 0.313,0.198 10 false *I 4.99,5.656 5.302,5.854 0.313,0.198 10 false *j
*1 Center Body Pillar Upper Reinforce - -