Home › Vehicle Exterior › BODY PANEL › QUARTER PANEL(for 3 Door)
BM27T0E _01 Vehicle Exterior _054380 BODY WELD POINT _0264641 QUARTER PANEL(for 3 Door) F

BODY WELD POINT  QUARTER PANEL(for 3 Door)  ASSEMBLY REPLACEMENT  


K132816

Weld work for 980 MPa ultra high strength steel


1.

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

*a: When welding 2 panels together including 980 MPa ultra high strength steel.

Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 18 Cyc. (0.30 Sec.)
Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

*b: When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a panel to the welded panels with the weld condition above.)

Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

HINT:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108828

Cut Location for Supply Parts

REMOVAL POINT
1.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


K132850

K132851C01
0.385,0.24 0.698,0.396 0.313,0.156 10 false *A 0.656,4.656 0.969,4.813 0.313,0.156 10 false *B
*A LH *B RH



INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108831

Butt Weld
K108834

Body Sealer

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

Follow the welding conditions when welding point *b to assure sufficient weld strength. (See the introduction)

4.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer evenly about 5 mm (0.20 in.) from the flange, avoiding any oozing.

Apply body sealer evenly, about 3 to 4 mm (0.12 to 0.16 in.) in diameter.


5.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

6.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

7.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K132852C01
4.396,7.885 4.646,7.219 false 5.469,6.365 5.896,5.938 5.896,5.938 5.417,6.917 false 4.719,4.135 4.969,4.302 0.25,0.167 10 false *A 4.708,4.333 4.948,4.521 0.24,0.188 10 false *B 5.948,5.802 6.26,5.958 0.313,0.156 10 false *1 4.302,7.927 4.615,8.083 0.313,0.156 10 false *2 6.646,8.469 6.958,8.625 0.313,0.156 10 false *c 1.188,3.073 1.5,3.271 0.313,0.198 10 false *b 1.49,2.719 1.802,2.917 0.313,0.198 10 false *b 1.917,3.927 2.229,4.125 0.313,0.198 10 false *b 0.896,6.719 1.438,6.958 0.542,0.24 10 false 5 (0.20)
*A LH *B RH
*1 Rivets *2 Fuel Filler Opening Lid
*c mm (in.) - -


K132853C01
0.292,0.354 0.604,0.51 0.313,0.156 10 false *A 0.438,4.594 0.75,4.75 0.313,0.156 10 false *B
*A LH *B RH