Home › Vehicle Exterior › BODY PANEL › REAR FLOOR PAN(for 3 Door)
BM27T0E _01 Vehicle Exterior _054380 BODY WELD POINT _0264647 REAR FLOOR PAN(for 3 Door) F

BODY WELD POINT  REAR FLOOR PAN(for 3 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K132823

With the body lower back panel and rear floor crossmember upper gusset removed.


REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108829

Cut Location

REMOVAL POINT
1.

Remove the rear floor side panel at the same time.


K132873C01
0.542,4.344 0.854,4.5 0.313,0.156 10 false *A 6.146,1.854 7,2.125 0.854,0.271 10 false 440 (17.32) 6.604,8.49 6.917,8.688 0.313,0.198 10 false *a
*A LH Side - -
*a mm (in.) - -


K132874C01
3.125,1.906 4.385,2.438 false 0.271,0.354 0.583,0.51 0.313,0.156 10 false *A 2.823,1.813 3.063,2.031 0.24,0.219 10 false *1
*A RH Side - -
*1 Rear Floor Side Panel - -



INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108829

Cut Location
K108830

Fillet Weld
K108834

Body Sealer

INSTALLATION POINT
1.

If the entire supply part is not needed, remove the part of the supply part that is needed.

2.

Cut the new part so that it overlaps the previous cut location by approximately 20 mm (0.79 in.).

3.

Before temporarily installing the new parts, weld the jack bracket and weld bolt with the standard number of welding points.

4.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

5.

*a: Perform plug-welding in the area where the panel are overlapped. Apply body sealer to both sides of each

HINT:
·

Confirm that the panels are securely welded together.

·

Apply body sealer in an even, continuous bead.



6.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

7.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K132875C01
4.656,3.865 4.656,3.177 false 0.552,0.427 0.865,0.583 0.313,0.156 10 false *A 0.698,4.594 1.01,4.75 0.313,0.156 10 false *B 4.594,3.948 4.906,4.104 0.313,0.156 10 false *1 2.073,8.156 2.302,8.385 0.229,0.229 10 false *2 6.479,8.448 6.792,8.604 0.313,0.156 10 false *b 5.073,2.052 6.292,2.365 1.219,0.313 10 false 420 (16.54)
*A Upper Face *B Lower Face
*1 Jack Bracket *2 Weld Bolt
*b mm (in.) - -


K132876N01
2.958,6.354 3.542,6.354 false 2.781,0.854 3.094,1.052 0.313,0.198 10 false *a 2.75,6.26 2.969,6.542 0.219,0.281 10 false *a

K132877C01
3.667,5.844 4.594,6.656 false 0.479,0.51 0.792,0.667 0.313,0.156 10 false *A 0.531,4.729 0.844,4.885 0.313,0.156 10 false *B 3.438,5.656 3.656,5.885 0.219,0.229 10 false *1
*A LH Side *B RH Side
*1 Rear Floor Side Panel - -