Home › Vehicle Exterior › BODY PANEL › ROOF PANEL(for Sliding Roof)
BM27T0E _01 Vehicle Exterior _054380 BODY WELD POINT _0264659 ROOF PANEL(for Sliding Roof) F

BODY WELD POINT  ROOF PANEL(for Sliding Roof)  ASSEMBLY REPLACEMENT  


3 Door


K132828

a.

REMOVAL

Symbol Meaning
K108818

Remove Weld Points

REMOVAL POINT
1.

If reusing the roof panel reinforcement, trim the hemming location using a disc sander, etc.


K132888C01
0.938,5.479 1.167,4.792 false 0.823,5.573 1.135,5.729 0.313,0.156 10 false *a 2.177,5.042 2.49,5.198 0.313,0.156 10 false *b
*a Disc Sander *b Hemming Location



b.

INSTALLATION

Symbol Meaning
K108823

Plug Weld
K108834

Body Sealer

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

After the roof panel reinforcement is welded to the new parts, install the roof panel to the vehicle side.

4.

Before temporarily installing the new parts, apply body sealer to the windshield header panel and roof panel reinforcement.

HINT:

Apply just enough body sealer for the new parts to make contact.


5.

Bend the flange hem with a wooden hammer and dolly.

HINT:

Perform hemming three steps, being careful not to warp the panel.


6.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

7.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K132889

K132890C01
1.125,4.396 0.823,4.031 false 1.896,4.25 1.5,4.49 false 1.365,5.417 1.104,5.115 false 0.646,3.844 0.958,4 0.313,0.156 10 false *a 1.948,4.156 2.26,4.313 0.313,0.156 10 false *b 1.438,5.417 1.75,5.573 0.313,0.156 10 false *c
*a Dolly *b Cloth Tape
*c Wooden Hammer - -




5 Door


K125787

a.

REMOVAL

Symbol Meaning
K108818

Remove Weld Points

REMOVAL POINT
1.

If reusing the roof panel reinforcement, trim the hemming location using a disc sander, etc.


K125864C02
0.802,5.438 1.052,4.896 false 0.719,5.479 1.031,5.635 0.313,0.156 10 false *a 1.979,5.167 2.292,5.323 0.313,0.156 10 false *b
*a Disc Sander *b Hemming Location



b.

INSTALLATION

Symbol Meaning
K108823

Plug Weld
K108834

Body Sealer

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

After the roof panel reinforcement is welded to the new parts, install the roof panel to the vehicle side.

4.

Before temporarily installing the new parts, apply body sealer to the windshield header panel and roof panel reinforcement.

HINT:

Apply just enough body sealer for the new parts to make contact.


5.

Bend the flange hem with a wooden hammer and dolly.

HINT:

Perform hemming three steps, being careful not to warp the panel.


6.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

7.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K125865

K125866C02
1.344,5.51 1.479,5.802 false 1.49,4.771 1.302,4.427 false 2,4.625 1.76,4.854 false 1.198,4.24 1.51,4.396 0.313,0.156 10 false *a 2.031,4.427 2.25,4.615 0.219,0.188 10 false *b 1.417,5.813 1.729,5.969 0.313,0.156 10 false *c
*a Dolly *b Cloth Tape
*c Wooden Hammer - -