Home › Vehicle Exterior › BODY PANEL › FIT STANDARD / ADJUSTMENT METHOD › 2015.06–2017.08
BM27T0E _01 Vehicle Exterior _054380 BODY WELD POINT _0264660 FIT STANDARD / ADJUSTMENT METHOD F

BODY WELD POINT  FIT STANDARD / ADJUSTMENT METHOD  ADJUSTMENT  


INSPECT HOOD SUB-ASSEMBLY


a.

Check that the clearance measurements of areas A through F are within each standard range.

B365417E03
2.688,2.802 3,3.052 0.313,0.25 10 false A 0.885,0.917 1.198,1.167 0.313,0.25 10 false B 4.354,0.5 4.667,0.75 0.313,0.25 10 false C 4.917,0.583 5.229,0.833 0.313,0.25 10 false D 5.771,0.417 6.083,0.667 0.313,0.25 10 false E 6.25,0.583 6.563,0.833 0.313,0.25 10 false F

Standard:
Area Measurement Area Measurement
A
Reference
7.5 to 10.5 mm (0.295 to 0.413 in.) B
Reference
3.55 to 6.55 mm (0.140 to 0.258 in.)
C 2.0 to 5.0 mm (0.0787 to 0.197 in.) D -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
E 2.0 to 5.0 mm (0.0787 to 0.197 in.) F -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Centering bolts are used to mount the hood hinge and hood lock. The hood and hood lock cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

Centering bolts are used to mount the hood hinge and hood lock. The hood and hood lock cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.





ADJUST HOOD SUB-ASSEMBLY


a.

Adjust the hood position.

i.
B238464

Loosen the 4 hinge bolts on the hood.


ii.

Move the hood and adjust the clearance between the hood and front fender.


iii.

Tighten the 4 hinge bolts on the hood.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



b.

Adjust the height of the front end of the hood using the cushion rubbers.

i.
B360313

Adjust the 2 cushion rubbers so that the heights of the hood and fender are aligned.

HINT:

Raise or lower the front end of the hood by turning the 2 cushion rubbers.




c.

Adjust the hood lock.

i.
B238466

Loosen the 3 bolts.


ii.

Adjust the hood lock and tighten the 3 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


iii.

Check that the striker can smoothly engage with the hood lock.




INSPECT FRONT DOOR


a.

for 5 Door:

i.

Check that the clearance measurements of areas A through P are within the standard range.

B237269E03
1.896,0.552 2.167,0.833 0.271,0.281 10 false A 2.25,0.917 2.469,1.198 0.219,0.281 10 false B 3.823,0.385 4.083,0.667 0.26,0.281 10 false C 3.917,0.75 4.115,1.031 0.198,0.281 10 false D 5.25,0.333 5.417,0.531 0.167,0.198 10 false E 5.396,0.719 5.583,1 0.188,0.281 10 false F 5.802,1.417 6,1.698 0.198,0.281 10 false G 6.385,1.719 6.583,2 0.198,0.281 10 false H 5.583,3.083 5.802,3.365 0.219,0.281 10 false I 6.333,3.302 6.604,3.583 0.271,0.281 10 false J 4.813,4.135 5.083,4.417 0.271,0.281 10 false K 4.917,3.667 5.188,3.948 0.271,0.281 10 false L 3.25,4.219 3.51,4.5 0.26,0.281 10 false M 3.333,3.583 3.594,3.865 0.26,0.281 10 false N 1.25,2.833 1.583,3.115 0.333,0.281 10 false O 1.583,3.219 1.917,3.5 0.333,0.281 10 false P

Standard:
Area Measurement Area Measurement
A 3.60 to 6.60 mm (0.142 to 0.260 in.) B 6.50 to 9.50 mm (0.256 to 0.374 in.)
C 3.70 to 6.70 mm (0.146 to 0.264 in.) D 3.70 to 6.70 mm (0.146 to 0.264 in.)
E 3.70 to 6.70 mm (0.146 to 0.264 in.) F 4.60 to 7.60 mm (0.181 to 0.299 in.)
G 2.5 to 6.5 mm (0.0984 to 0.256 in.) H -2.0 to 2.0 mm (-0.0787 to 0.0787 in.)
I 3.0 to 6.0 mm (0.118 to 0.236 in.) J -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
K 4.05 to 7.05 mm (0.159 to 0.278 in.) L 4.45 to 7.45 mm (0.175 to 0.293 in.)
M 4.05 to 7.05 mm (0.159 to 0.278 in.) N 4.35 to 7.35 mm (0.171 to 0.289 in.)
O 2.7 to 5.7 mm (0.106 to 0.224 in.) P -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)




b.

for 3 Door:

i.

Check that the clearance measurements of areas A through P are within the standard range.

B237270E02
1.917,0.583 2.188,0.865 0.271,0.281 10 false A 2.198,0.969 2.417,1.25 0.219,0.281 10 false B 3.823,0.385 4.083,0.667 0.26,0.281 10 false C 3.917,0.75 4.115,1.031 0.198,0.281 10 false D 5.25,0.333 5.5,0.531 0.25,0.198 10 false E 5.417,0.719 5.604,1 0.188,0.281 10 false F 5.75,1.417 5.948,1.698 0.198,0.281 10 false G 6.333,1.719 6.531,2 0.198,0.281 10 false H 5.583,3.135 5.802,3.417 0.219,0.281 10 false I 6.313,3.302 6.583,3.583 0.271,0.281 10 false J 4.729,4.25 5,4.531 0.271,0.281 10 false K 4.833,3.583 5.104,3.865 0.271,0.281 10 false L 3.25,4.219 3.51,4.5 0.26,0.281 10 false M 3.25,3.552 3.51,3.833 0.26,0.281 10 false N 1.25,2.833 1.583,3.115 0.333,0.281 10 false O 1.583,3.219 1.917,3.5 0.333,0.281 10 false P

Standard:
Area Measurement Area Measurement
A 3.60 to 6.60 mm (0.142 to 0.260 in.) B 6.50 to 9.50 mm (0.256 to 0.374 in.)
C 3.70 to 6.70 mm (0.146 to 0.264 in.) D 3.70 to 6.70 mm (0.146 to 0.264 in.)
E 3.70 to 6.70 mm (0.146 to 0.264 in.) F 4.60 to 7.60 mm (0.181 to 0.299 in.)
G 3.5 to 6.5 mm (0.138 to 0.256 in.) H -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
I 2.7 to 5.7 mm (0.106 to 0.224 in.) J -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
K 4.05 to 7.05 mm (0.159 to 0.278 in.) L 4.45 to 7.45 mm (0.175 to 0.293 in.)
M 4.05 to 7.05 mm (0.159 to 0.278 in.) N 4.35 to 7.35 mm (0.171 to 0.289 in.)
O 2.7 to 5.7 mm (0.106 to 0.224 in.) P -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)





HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed on it. Substitute the centering bolts with standard bolts when making adjustments.



ADJUST FRONT DOOR


a.
B237271

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the vehicle body.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B237272

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


f.

Using a brass bar and hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT REAR DOOR


a.

Check that the clearance measurements of areas A through N are within the standard range.

B237274E02
2.708,0.333 2.906,0.552 0.198,0.219 10 false A 2.854,0.688 3.052,0.906 0.198,0.219 10 false B 4.26,0.313 4.458,0.531 0.198,0.219 10 false C 4.448,0.688 4.646,0.906 0.198,0.219 10 false D 6.167,1.594 6.365,1.813 0.198,0.219 10 false E 6.385,1.813 6.583,2.031 0.198,0.219 10 false F 4.833,4.25 5.031,4.469 0.198,0.219 10 false G 5.135,3.667 5.333,3.885 0.198,0.219 10 false H 3.146,3.948 3.344,4.167 0.198,0.219 10 false I 2.896,3.333 3.146,3.552 0.25,0.219 10 false J 0.833,3.417 1.073,3.635 0.24,0.219 10 false L 1.167,2.781 1.417,3 0.25,0.219 10 false K 0.667,1.865 0.906,2.083 0.24,0.219 10 false N 1.448,1.281 1.698,1.5 0.25,0.219 10 false M

Standard:
Area Measurement Area Measurement
A 3.7 to 6.7 mm (0.146 to 0.264 in.) B 4.2 to 7.2 mm (0.165 to 0.284 in.)
C 3.6 to 6.6 mm (0.142 to 0.260 in.) D 4.9 to 7.9 mm (0.193 to 0.311 in.)
E 2.7 to 5.7 mm (0.106 to 0.224 in.) F -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
G 4.05 to 7.05 mm (0.159 to 0.278 in.) H 4.6 to 7.6 mm (0.181 to 0.299 in.)
I 4.05 to 7.05 mm (0.159 to 0.278 in.) J 4.6 to 7.6 mm (0.181 to 0.299 in.)
K 3.0 to 6.0 mm (0.118 to 0.236 in.) L -1.5 to 1.5 mm (-0.0591 to 0.0591 in.)
M 2.5 to 6.5 mm (0.0984 to 0.256 in.) N -2.0 to 2.0 mm (-0.0787 to 0.0787 in.)


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.





ADJUST REAR DOOR


a.
B237275

Using SST, loosen the hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the hinge bolts on the vehicle body.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B237273

Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws.


f.

Using a brass bar and hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the striker mounting screws.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)



INSPECT BACK DOOR


a.

w/ Back Door Tire Carrier:

i.

Check that the clearance measurements of areas A through I are within the standard range.

B241628E02
1.167,0.417 1.344,0.667 0.177,0.25 10 false A 5.302,0.833 5.583,1.083 0.281,0.25 10 false B 6,3 6.281,3.25 0.281,0.25 10 false E 4.885,2.75 5.167,3 0.281,0.25 10 false F 2.75,2 3.031,2.25 0.281,0.25 10 false H 6.083,1.083 6.365,1.333 0.281,0.25 10 false C 6.5,1.917 6.781,2.167 0.281,0.25 10 false D 3.25,3 3.531,3.25 0.281,0.25 10 false I 3.083,1.083 3.365,1.333 0.281,0.25 10 false G

Standard:
Area Measurement Area Measurement
A 8.35 to 11.35 mm (0.329 to 0.447 in.) B 4.65 to 7.65 mm (0.183 to 0.301 in.)
C 5.05 to 8.05 mm (0.199 to 0.317 in.) D 5.25 to 8.25 mm (0.207 to 0.325 in.)
E 5.25 to 8.25 mm (0.207 to 0.325 in.) F 8.85 to 11.85 mm (0.348 to 0.467 in.)
G 4.85 to 7.85 mm (0.191 to 0.309 in.) H 5.25 to 8.25 mm (0.207 to 0.325 in.)
I 5.25 to 8.25 mm (0.207 to 0.325 in.) - -




b.

w/o Back Door Tire Carrier:

i.

Check that the clearance measurements of areas A through I are within the standard range.

B241629E02
1.25,0.583 1.5,0.823 0.25,0.24 10 false A 5.188,0.844 5.5,1.083 0.313,0.24 10 false B 6.104,1.083 6.417,1.323 0.313,0.24 10 false C 6.5,1.927 6.688,2.167 0.188,0.24 10 false D 6.021,3.01 6.333,3.25 0.313,0.24 10 false E 4.51,2.677 4.667,2.917 0.156,0.24 10 false F 3.135,1.083 3.333,1.323 0.198,0.24 10 false G 2.75,1.927 3.063,2.167 0.313,0.24 10 false H 3.25,3.01 3.396,3.25 0.146,0.24 10 false I

Standard:
Area Measurement Area Measurement
A 8.35 to 11.35 mm (0.329 to 0.447 in.) B 5.05 to 8.05 mm (0.199 to 0.317 in.)
C 4.65 to 7.65 mm (0.183 to 0.301 in.) D 4.95 to 7.95 mm (0.195 to 0.313 in.)
E 4.95 to 7.95 mm (0.195 to 0.313 in.) F 8.85 to 11.85 mm (0.348 to 0.467 in.)
G 4.65 to 7.65 mm (0.183 to 0.301 in.) H 4.95 to 7.95 mm (0.195 to 0.313 in.)
I 5.05 to 8.05 mm (0.199 to 0.317 in.) - -





HINT:

Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.


ADJUST BACK DOOR


a.

w/ Back Door Tire Carrier:

i.

Remove the spare wheel cover pad.


ii.

Remove the spare wheel cover.


iii.

Remove the spare tire.



b.
B237277E01
0.043,0 0.263,0.205 0.219,0.205 10 *A 0.043,2.251 0.263,2.456 0.219,0.205 10 *B

Loosen the hinge bolts on the body and adjust the position of the door.

Text in Illustration
*A w/ Back Door Tire Carrier
*B w/o Back Door Tire Carrier


c.

Tighten the hinge bolts on the body.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


d.
B237278E03
0.083,0.083 0.5,0.417 0.417,0.333 10 true *A 0.083,2.271 0.5,2.583 0.417,0.313 10 true *B

Loosen the hinge bolts on the door and adjust the position of the door.

Text in Illustration
*A w/ Back Door Tire Carrier
*B w/o Back Door Tire Carrier


e.

Tighten the hinge bolts on the door.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


f.
B243388

Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and then hitting the striker with a plastic-faced hammer.


g.

Using a T40 "TORX" socket, tighten the striker mounting screws.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


h.
B133659

Using a T30 "TORX" socket, adjust the back door side male stopper position by slightly loosening the stopper mounting screws and then hitting the stopper with a plastic-faced hammer.


i.

Using a T30 "TORX" socket, tighten the male stopper mounting screws.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


j.
B129932

Loosen the back door side female stopper bolts and adjust the stopper position.


k.

Tighten the female stopper bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


l.

w/ Back Door Tire Carrier:

i.

Install the spare tire.


ii.

Install the spare wheel cover.


iii.

Install the spare wheel cover pad.