Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR (for 5 Door) › 2015.06–2017.08
BM27T0E _01 Vehicle Exterior _054380 BODY WELD POINT _0267621 CENTER BODY PILLAR(for 5 Door) F

BODY WELD POINT  CENTER BODY PILLAR(for 5 Door)  CUT AND JOIN REPLACEMENT SECTIONS  


K125768

Weld work for 980 MPa ultra high strength steel


1.

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

*a: When welding 2 panels together including 980 MPa ultra high strength steel.

Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 18 Cyc. (0.30 Sec.)
Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

*b: When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a panel to the welded panels with the weld condition above.)

Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

HINT:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts

REMOVAL POINT
1.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)

2.

*c indicates welds to remove for easier removal.

3.

*d indicates the location of the foamed sealing material. Be careful when cutting as the foamed sealing material is located near the cutting position.

4.

*e is reused.


K125806C02
1.063,1.958 1.271,2.146 0.208,0.188 10 false *c 2.917,2.115 3.125,2.302 0.208,0.188 10 false *c 6.583,8.5 6.896,8.698 0.313,0.198 10 false *h 1.021,6.021 1.646,6.219 0.625,0.198 10 false 80 (3.15)
*h mm (in.) - -


K125807C02
1.281,1.271 1.042,0.906 false 1.698,1.323 1.552,1.031 false 2.865,1.052 2.531,1.219 false 6.677,8.573 6.99,8.729 0.313,0.156 10 false *h 0.906,0.729 1.104,0.917 0.198,0.188 10 false *d 2.885,0.896 3.198,1.094 0.313,0.198 10 false *d 1.448,0.865 1.76,1.063 0.313,0.198 10 false *e 2.594,0.698 3.969,0.896 1.375,0.198 10 false 20 (0.79) 0.635,1.927 1.292,2.167 0.656,0.24 10 false 245 (9.65) 2.646,1.781 3.5,1.99 0.854,0.208 10 false 320 (12.60) 0.552,5.313 1.125,5.708 0.573,0.396 10 false 10 (0.39)
*h mm (in.) - -



INSTALLATION


Symbol Meaning
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108830

Fillet Weld
K108831

Butt Weld

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

Follow the welding conditions when welding point *a to assure sufficient weld strength. (See the introduction)

4.

Follow the welding conditions when welding point *b to assure sufficient weld strength. (See the introduction)

5.

After welding the center body inner pillar to the vehicle side, install the center body pillar upper reinforce.

6.

After welding the center body pillar upper reinforce to the vehicle side, install the center body outer pillar.

7.

*f indicates the location of the foamed sealing material. Be careful when welding as the foamed sealing material is located near the area that is cut and joined together.

8.

After welding the center body inner pillar and center body pillar upper reinforce to the vehicle side, install the center body outer pillar and *g.

9.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

10.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

11.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K125808C02
3.167,1.917 4.104,2.052 false 2.99,1.823 3.156,2.083 0.167,0.26 10 false *1 6.635,8.542 6.948,8.698 0.313,0.156 10 false *h 2.979,2.823 3.292,3.021 0.313,0.198 10 false *a 3.448,2.802 3.76,3 0.313,0.198 10 false *a 3.656,3.885 3.896,4.094 0.24,0.208 10 false *a 0.948,7.281 1.583,7.51 0.635,0.229 10 false 50 (1.97) 2.354,7.26 2.99,7.49 0.635,0.229 10 false 50 (1.97)
*1 Center Body Inner Pillar - -
*h mm (in.) - -


K125809C02
4.531,5.385 5.365,5.083 false 5.396,5 5.708,5.156 0.313,0.156 10 false *1 1.24,6.115 1.438,6.313 0.198,0.198 10 false *a 1.646,6.24 1.844,6.438 0.198,0.198 10 false *a 3.656,7.563 3.885,7.74 0.229,0.177 10 false *a
*1 Center Body Pillar Upper Reinforce - -


K125810C02
2.906,5.156 4,5.396 false 1.656,1.292 1.375,0.875 false 2.063,1.271 1.813,0.844 false 3.167,0.76 2.865,1.188 false 3.208,6.51 3.521,6.708 0.313,0.198 10 false *b 2.781,6.698 3.094,6.896 0.313,0.198 10 false *b 3.104,7.917 3.302,8.094 0.198,0.177 10 false *b 3.552,7.708 3.76,7.875 0.208,0.167 10 false *b 2.719,5.063 2.896,5.281 0.177,0.219 10 false *1 1.229,0.688 1.417,0.875 0.188,0.188 10 false *f 1.677,0.615 1.948,0.792 0.271,0.177 10 false *g 3.188,0.583 3.458,0.76 0.271,0.177 10 false *f
*1 Center Body Outer Pillar - -