Home › Vehicle Exterior › BODY PANEL › ROCKER PANEL(for 3 Door)
BM27T0E _01 Vehicle Exterior _054380 BODY WELD POINT _0267625 ROCKER PANEL(for 3 Door) F

BODY WELD POINT  ROCKER PANEL(for 3 Door)  ASSEMBLY REPLACEMENT  


K132815

Weld work for 980 MPa ultra high strength steel


1.

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)

*a: When welding 2 panels together including 980 MPa ultra high strength steel.

Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 18 Cyc. (0.30 Sec.)
Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

*b: When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a panel to the welded panels with the weld condition above.)

Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas

HINT:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.



REMOVAL


Symbol Meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108827

Cut and Join Location

REMOVAL POINT
1.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)


K132844C01
6.594,8.51 6.906,8.667 0.313,0.156 10 false *c 2.083,6.26 3.458,6.458 1.375,0.198 10 false 15 (0.59) 3.229,2.792 3.927,3 0.698,0.208 10 false 140 (5.51)
*c mm (in.) - -


K132845


INSTALLATION


Symbol Meaning
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108831

Butt Weld
K108834

Body Sealer

INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

Follow the welding conditions when welding point *a to assure sufficient weld strength. (See the introduction)

4.

Follow the welding conditions when welding point *b to assure sufficient weld strength. (See the introduction)

5.

After welding the rocker panel reinforcement to the vehicle side, install the front body upper outer pillar, center body outer pillar and quarter panel.

6.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


7.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

8.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

9.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K132846C01
3.167,2.615 3.167,2.031 false 2.156,6.146 2.469,6.344 0.313,0.198 10 false *a 2.375,6.5 2.688,6.698 0.313,0.198 10 false *a 2.875,6.5 3.188,6.698 0.313,0.198 10 false *a 3.219,6.188 3.531,6.385 0.313,0.198 10 false *a 3.583,5.854 3.896,6.052 0.313,0.198 10 false *a 4.042,5.552 4.354,5.75 0.313,0.198 10 false *a 2.74,7.604 2.948,7.792 0.208,0.188 10 false *a 3.76,7.646 3.969,7.833 0.208,0.188 10 false *a 3.958,4.521 4.167,4.708 0.208,0.188 10 false *a 2.01,2.271 2.219,2.458 0.208,0.188 10 false *a 4.208,2.26 4.417,2.448 0.208,0.188 10 false *a 3.104,2.646 3.313,2.833 0.208,0.188 10 false *1
*1 Rocker Panel Reinforcement - -


K132847C01
2.063,4.042 2.063,2.906 false 2.458,1.76 2.771,1.958 0.313,0.198 10 false *a 2.427,3.094 2.74,3.292 0.313,0.198 10 false *a 5.146,3.354 5.458,3.552 0.313,0.198 10 false *a 2,4.115 2.313,4.271 0.313,0.156 10 false *1
*1 Rocker Panel Reinforcement - -


K132848C01
0.958,5.573 1.813,4.573 false 3.292,6.021 3.292,4.813 false 5.865,5.167 5.208,4.635 false 0.802,5.594 1.115,5.75 0.313,0.156 10 false *1 3.219,6.083 3.531,6.24 0.313,0.156 10 false *2 5.917,5.167 6.229,5.323 0.313,0.156 10 false *3 1.854,5 2.167,5.198 0.313,0.198 10 false *b 2.781,4.99 3.094,5.188 0.313,0.198 10 false *b 3.917,4.99 4.229,5.188 0.313,0.198 10 false *b 3.104,3.573 3.417,3.771 0.313,0.198 10 false *b 3.479,3.948 3.792,4.146 0.313,0.198 10 false *b
*1 Front Body Upper Outer Pillar *2 Rocker Panel Reinforcement
*3 Quarter Panel - -


K132849C01
2.823,7.115 2.229,6.615 false 2.188,3.688 2.188,2.75 false 2.938,2.219 3.51,1.771 false 3.563,1.635 3.875,1.792 0.313,0.156 10 false *1 2.104,3.74 2.417,3.896 0.313,0.156 10 false *2 2.104,6.438 2.417,6.594 0.313,0.156 10 false *3
*1 Front Body Upper Outer Pillar *2 Rocker Panel Reinforcement
*3 Quarter Panel - -